Energy efficiency of RF Frontends (RFFE), especially transmitters, continues to gain greater prominence.Meeting the efficiency challenge is increasingly difficult at higher operating frequencies and bandwidths, such as those proposed for 5G.There is a group of transmitter RFFE architectures whose signal output is constructed from two, or more, efficiently generated components. This signal construction in effect, means that such architectures use predictive, post-correction linearization. Their predictive nature enables distortion to be completely eliminated.The capabilities of multi-channel signal synthesis setups with R&S®SMW200A, in combination with the R&S®FSW analyzer enable measurement, hence development, of these types of transmitters.The document focusses on devices for the 3.5 GHz NR (5G New Radio) candidate band, but its findings are equally applicable to developments and measurements for, for example, K-band satellite applications or mmW NR candidate bands, where efficiency is an even more crucial design target.

01-Aug-2017 | AN-No. 1MA289

The aim of this application note is to provide information regarding Rohde & Schwarz instrument drivers. This paper shall help application engineers and software developers to easily get an understanding of advanced techniques to develop test and measurement (T&M) applications by utilizing Rohde & Schwarz instrument drivers. Furthermore the nomenclature used for Rohde & Schwarz instrument drivers will be explained.

01-Jan-2013 | AN-No. 1MA153

When installed on an Apple iPad*, a remote desktop app provides a convenient way to remotely control measuring instruments over a WLAN connection.This is especially helpful when using measuring instruments that do not have their own display such as the R&S®VTS or R&S®SFC.The remote desktop app also gives users a detached way to control the instrument if, for example, the actual measuring instrument is installed in a place that is difficult to access.* Apple and iPad are trademarks of Apple Inc.

02-Oct-2012 | AN-No. 7BM82

Simultaneous DL throughput verification and UL transmission testing with the R&S®CMW500

29-Jul-2009

This application note describes three ways of generating multicarrier signals with high dynamic range for testing power amplifiers of 3GPP radio base stations. The corresponding sets of waveform (*.wv) files are delivered with this application note. The WinIQSIM™ software is used to download these files to the signal generator(s).Tips for optimizing spectrum analyzer settings in order to measure the Adjacent Channel Leakage Ratio (ACLR) are given.

17-Feb-2005 | AN-No. 1MA48

This white paper introduces a novel attribute based architecture for VXIplug&play instrument drivers. The presented architecture uses the attribute based concept of IVI-C instrument drivers to introduce a two-layer design for VXIplug&play instrument drivers. Moreover the use of attributes is shown for the Rohde & Schwarz Spectrum Analyzer (rsspecan) instrument driver.

01-Dec-2012 | AN-No. 1MA170

This application note provides a brief introduction into the capabilities of the Rohde & Schwarz Vector Signal Generators (VSG) to create user defined digitally modulated signals called Custom Digital Modulation (CDM). Additionally an in depth description of the functions and the operation of the CDM-Toolbox is provided. The CDM-Toolbox is application software which allows an easy remote configuration of CDM signals on Rohde & Schwarz VSGs but also the creation of data list and control list files which are most useful to further extend the application area of CDM signals.

24-Jul-2017 | AN-No. 1GP96

This application note describes different measurement techniques and methods for an automotive lighting module based on a hybrid controller design. Of course, a lighting module in such an environment has to fulfil requirements according to the automotive standard, which is typically a relatively high-level standard compare to the industry standard. The oscilloscope is a perfect tool for this application to verify the set of requirements because time domain signals (analog and digital) are present in the whole design. Furthermore, measurements in the frequency domain have to be performed, which a modern oscilloscope can fulfil. In addition to the oscilloscope, a programmable power supply supports the measurement in several measurements. The set of requirements are the main reason why a hybrid controller from Microchip is a great choice for this design because it provides tremendous analogue and digital capabilities. The hybrid controller provides beside the analogue functions like an operational amplifier digital functions like analog-to-digital converter and interface functions like UART, CAN or LIN to interact with other systems. The programmable software part is hosted in the digital part. The digital part of the controller implements the communication interface and provides status information to the outer system controller. The light source itself has to avoid any flicker and shall be capable to dim to different lighting levels. Wide input voltage variations and efficiency have to be taken into account during the design of a converter dedicated for automotive applications. Nevertheless, the measurement considerations presented with the design are valid and applicable in other professional lighting industries as well.Thanks to Mr. Andreas Reiter and Mr. Milan Marjanovic from Microchip who provided us with hardware and software and their great expertise to create this application note.

08-Jun-2020 | AN-No. GFM339

This application note describes how to measure balanced reflection mixed mode S-Parameters with a 2-port Network Analyzer like R&S® ZVL. The application note directly transfers S-Parameter Trace Data from R&S® Network Analyzers to Microsoft™ Excel™ using a direct connection like GPIB or LAN and does the mode conversion to Mixed Mode inside Excel™ with a VBA Macro.

14-Feb-2008 | AN-No. RSI05

Its excellent realtime baseband performance in combination with its ability to easily import the scattering parameters of an active/passive twoport interconnection network via s2p-files make the R&S®SMW200A vector signal generator ideal for high-precision RF and microwave tests requiring deembedding of the device under test (DUT).

11-Oct-2017

Capturing small ECG signals in medical applications The R&S®RTE is the best choice for analyzing small signals such as ECG signals with high signal fidelity. Capturing small ECG signals in medical applications Capturing small ECG signals in medical applications The R&S®RTE is the best choice for analyzing small signals such as ECG signals with high signal fidelity. Capturing small ECG signals in medical

17-Nov-2015

The general characterization of complex DUTs such as amplifiers requires the measurement of several parameters. Some may require more than one test device or expensive equipment. Thanks to its versatility, the R&S®ZNL is an economic solution that can characterize a variety of DUTs both via network analysis and spectrum analysis.

17-Dec-2021

The OneWeb satellite constellation provides global broadband data access to almost every user. Via user terminals, the satellite connects the remote users to the ground station, which has access to the terrestrial broadband network. Receivers and RF equipment in the OneWeb ground stations and the user terminals need to handle high-speed microwave data links.

24-Apr-2018

combination test, optocouplers, compliance test, DUT, coupling factor, Combination test Expanded test method for optocouplers Combination test Expanded test method for optocouplers combination test, optocouplers, compliance test, DUT, coupling factor, Combination test Expanded test method for optocouplers Combination test Expanded test method for optocouplers combination test, optocouplers, compliance

17-Jul-2006

Most of the tests specified in standard TS 34.121 for 3GPP Rel-99 can be performed with R&S®CMW500. This document provides a step by step guide on how to perform Rel-99 measurements on transmitter/receiver characteristics, and performance tests according to TS 34.121 V9.5.0 clauses 5 and 6 with standalone R&S®CMW500. A set of *.sav files based on R&SCMW500 firmware V2.1.20 for UE supporting band I with power class 3 in RMC 12.2 kbps downlink/uplink is attached to this application note.

16-Dec-2011 | AN-No. 1CM95

Soft-start verification is becoming a major concern for modern switching mode power supplies due to the increasing use of digital controllers. The R&S®RTM3000 and R&S®RTA4000 oscilloscopes offer pulse width modulation (PWM) track analysis functionality, which is a great feature for verifying and optimizing soft start during development.

09-Jul-2019

Interferences on audio transmissions, which happens only from time to time, are very difficult to be measured. This application note describes a method, used by the audio analyzers UPL and UPD, to monitor test tones without any interruption and detecting even the shortest clicks.

04-Jun-1998 | AN-No. 1GA31

This document describes the direct test mode mechanisms for testing Bluetooth Low Energy devices and explains how the direct test mode connection is established. The R&S CMW uses a USB port for the direct test mode connection while the Equipment under Test (EUT) may provide a USB port, a serial port or even a 2-wire UART interface for this purpose. Installing or assigning the right driver for the EUT is the main configuration task on the R&S CMW. For EUTs with USB port, the R&S CMW provides a Bluetooth Low Energy USB driver which has to be assigned to the connected EUT.

14-Dec-2016 | AN-No. 1C105

When it comes to testing analog and digital TV and audio broadcast receivers in cars, special requirements must be met. Although suppliers ensure the receiver functionality, this functionality must be tested when the receiver is integrated into the car. When it comes to testing analog and digital TV and audio broadcast receivers in cars, special requirements must be met. Although suppliers guarantee the receiver functionality, this functionality must be tested when the receiver is integrated into the car.

19-Feb-2015

Test, calibrate and verify high-performance automotive radar sensors with the R&S®ATS1500C CATR antenna test system and the R&S®AREG100A automotive radar echo generator.

13-Jan-2020

This Application Note gives a short overview how signals with two different modulation schemes can be analyzed using the R&S®FSW (or R&S®FPS) using its Multi-Standard-Radio-Analyzer (MSRA) and Vector Signal Analysis personality. The Application Note focuses on DVB-S2(X) signals, but the approach may be used for similar signals as well, as e.g. used in microwave backhaul links.The Application Note also provides a software tool that automates the configuration and provides the variety of different constellations that are used within DVB-S2(X).

18-Apr-2016 | AN-No. 1EF93

The R&S®EDST300 efficiently and precisely analyzes TACAN and DME ground stations, making it ideal for commissioning and regular maintenance.

16-Feb-2017

radio signals, automatic monitoring, interference, RF radiation, frequency spectrum, Automatic monitoring of radio signals interfering with sensitive devices in hospitals Automatic monitoring of radio signals interfering with sensitive devices in hospitals radio signals, automatic monitoring, interference, RF radiation, frequency spectrum, Automatic monitoring of radio signals interfering with sensitive

04-Sep-2006

This Application Note describes how to test and perform measurements on mobile phones in compliance with the GSM standard using the R&S®CMU200 by means of the remote-control program CMUgo or manual operation.

24-May-2005 | AN-No. 1CM57

This application note addresses the diverse possibilities of interoperability between Rohde & Schwarz power sensors and Rohde & Schwarz signal generators. All current and many legacy Rohde & Schwarz signal generators offer the capability of directly connecting power sensors. This enables power measurements without the need of a base unit or separate PC to display the readings. Furthermore, sensors can be used for special tasks like filling a user correction table or continuously controlling levels at crucial points in the measurement configuration.

31-Aug-2023 | AN-No. 1GP141

The R&S®BTC broadcast test center generates DVB-C2 signals for receiver tests with a variety of simulated interference types. The selection tests stipulated by the DVB Project require a cable TV network with full channel load. Combining the R&S®BTC broadcast test center and the R&S®CLG cable load generator makes it quick and easy to create a flexible cable TV network with full channel load and to simulate all types of realistic interference, permitting tests in accordance with DVB.

30-Jul-2013 | AN-No. 7BM88

Autonomous and semi-autonomous vehicles rely on a complex hardware and software architecture to gather and exploit information from numerous radar sensors. To generate reliable data, the sensors require an unobstructed view of the surroundings. The bumpers or radomes mounted in front of the sensors must not impair radar functionality. This requires extensive testing of the deployed plastic parts and their underlying polymer structure. The R&S®QAR50 is the ideal tool to characterize the material properties of polymers and their influence on the quality of the radar signal at an early design stage and in quality control of material development.

24-Jun-2022

Heinz Mellein, Manuel Mielkech 8NT01 MIMO Channel,Field Measurements,MIMO Evaluation,R&STSMx,R&SROMES Assessing a MIMO Channel Heinz Mellein, Manuel Mielkech 8NT01 MIMO Channel,Field Measurements,MIMO Evaluation,R&STSMx,R&SROMES Related products

31-Aug-2017 | AN-No. 8NT01

IQWizard is a tool for loading IQ signal files in various formats and measuring IQ signals with a FSx spectrum analyzer or ESx Receiver. The obtained IQ data in memory can be stored in various formats or be transmitted to an R&S® vector signal generator with WinIQSIM™ or WinIQSIM2™.

26-Apr-2013 | AN-No. 1MA028

Next generation technologies in radar and satellite communication with high data rates call for innovative testing solutions to develop and manufacture RF components like voltage controlled oscillators (VCO). The R&S®FSPN phase noise analyzer increases efficiency and reproducibility of VCO characterization and phase noise measurements from lab to production.Voltage controlled oscillators are oscillators whose output frequency is controlled by means of an external tuning voltage, and they are used in a wide variety of electronic and RF applications like function generators, phase-locked loops including frequency synthesizers used in communication equipment. Different VCO design approaches yield different parameters and performance, and therefore it is important to measure or characterize VCOs under different conditions. This application note provides a short technical introduction to voltage controlled oscillators and explains the most common and the most important measurements made during the VCO characterization process.

17-May-2023 | AN-No. 1SL386