R&S®ZV-WRx/ZCWMxx waveguide calibration kits

up to 1100 GHz

R&S®ZV-WRx/ZCWMxx waveguide calibration kits
Abrir o Lightbox
R&S®ZV-WRx/ZCWMxx waveguide calibration kits
Abrir o Lightbox
R&S®ZV-WRx/ZCWMxx waveguide calibration kits
Abrir o Lightbox
R&S®ZV-WRx/ZCWMxx waveguide calibration kits
Abrir o Lightbox
R&S®ZV-WRx/ZCWMxx waveguide calibration kits
Abrir o Lightbox
R&S®ZV-WRx network analyzer calibration kits – waveguide, Front High R&S®ZV-WRx network analyzer calibration kits – waveguide, Side view R&S®ZV-WRx network analyzer calibration kits – waveguide, Side view R&S®ZV-WRx network analyzer calibration kits – waveguide, Side view R&S®ZV-WRx network analyzer calibration kits – waveguide, Side view

Key Facts

  • Waveguide calibration kit series covering 50 GHz to 1100 GHz
  • Including match, short, offset short
  • Optional version including sliding match
  • Calibration kit parameters pre-installed in R&S®VNAs
  • Calibration kit versions with sliding match available

Extending to the mmWave range

The R&S®ZV-WRxx calibration kit series provides waveguide calibration standards for system error correction of mmWave network analyzer setups. All common waveguide bands from 50 GHz to 1100 GHz are supported. The calibration kits contain short, offset short and match. Separate models with a sliding match are also available. The sets come with a hex ball driver and hex ball screws. The calibration kit data are pre-defined on each Rohde & Schwarz vector network analyzer, allowing for straightforward and reliable calibration.

Features & benefits

Sliding match models

Get high-end accuracy

There are extra models that include a sliding match. Using a sliding match instead of a fixed match further increases measurement accuracy.

ZV-WR10 kit with sliding match
Abrir o Lightbox

ZV-WR10 kit with sliding match

High mechanical stability

Short with offset margin for reliable results

Especially with the high-frequency kits, a bare lambda/4 shim standard is very thin, which can result in tensions and bending when connected and in poor accuracy. To ensure reliable results, the shim standard for some ZV-WRxx kits is designed with an additional offset length to ensure high mechanical stability and reproducible results. (Please note: the dedicated offset short is a different standard.)

Available models

Available models
Modelos
Type
Frequency range
Connector type
Calibration standards

R&S®ZV-WR02

Order Number 1314.5550.10

Type
Waveguide calibration kit
Frequency range
325 GHz to 500 GHz
Connector type
WR02
Calibration standards
Short, Offset Short, Match,  without sliding Match

R&S®ZV-WR03

Order Number 1307.7300.30

Type
Waveguide calibration kit
Frequency range
220 GHz to 325 GHz
Connector type
WR03
Calibration standards
without sliding match

R&S®ZV-WR03

Order Number 1307.7300.31

Type
Waveguide calibration kit
Frequency range
220 GHz to 325 GHz
Connector type
WR03
Calibration standards
with sliding match

R&S®ZV-WR05

Order Number 1307.8106.10

Type
Waveguide calibration kit
Frequency range
140 GHz to 220 GHz
Connector type
WR05
Calibration standards
without sliding match

R&S®ZV-WR05

Order Number 1307.8106.11

Type
Waveguide calibration kit
Frequency range
140 GHz to 220 GHz
Connector type
WR05
Calibration standards
with sliding match

R&S®ZV-WR06

Order Number 1311.8807.10

Type
Waveguide calibration kit
Frequency range
110 GHz to 170 GHz
Connector type
WR06
Calibration standards
without sliding match

R&S®ZV-WR06

Order Number 1311.8807.11

Type
Waveguide calibration kit
Frequency range
110 GHz to 170 GHz
Connector type
WR06
Calibration standards
with sliding match

R&S®ZV-WR08

Order Number 1307.7900.10

Type
Waveguide calibration kit
Frequency range
90 GHz to 140 GHz
Connector type
WR08
Calibration standards
without sliding match

R&S®ZV-WR08

Order Number 1307.7900.11

Type
Waveguide calibration kit
Frequency range
90 GHz to 140 GHz
Connector type
WR08
Calibration standards
with sliding match

R&S®ZV-WR10

Order Number 1307.7100.10

Type
Waveguide calibration kit
Frequency range
75 GHz to 110 GHz
Connector type
WR10
Calibration standards
without sliding match

R&S®ZV-WR10

Order Number 1307.7100.11

Type
Waveguide calibration kit
Frequency range
75 GHz to 110 GHz
Connector type
WR10
Calibration standards
with sliding match

R&S®ZV-WR12

Order Number 1307.7700.10

Type
Waveguide calibration kit
Frequency range
60 GHz to 90 GHz
Connector type
WR12
Calibration standards
without sliding match

R&S®ZV-WR12

Order Number 1307.7700.11

Type
Waveguide calibration kit
Frequency range
60 GHz to 90 GHz
Connector type
WR12
Calibration standards
with sliding match

R&S®ZV-WR15

Order Number 1307.7500.30

Type
Waveguide calibration kit
Frequency range
50 GHz to 75 GHz
Connector type
WR15
Calibration standards
without sliding match

R&S®ZV-WR15

Order Number 1307.7500.31

Type
Waveguide calibration kit
Frequency range
50 GHz to 75 GHz
Connector type
WR15
Calibration standards
with sliding match

R&S®ZCWM-1092

Order Number 3628.5699.02

Type
Waveguide Calibration Kit
Frequency range
170 GHz to 260 GHz
Connector type
WM-1092
Calibration standards
without sliding match

R&S®ZCWM-710

Order Number 1339.4070.02

Type
Waveguide Calibration Kit
Frequency range
260 GHz to 400 GHz
Connector type
WM-710
Calibration standards
without sliding match

R&S®ZCWM-570

Order Number 1322.3099.10

Type
Waveguide Calibration Kit
Frequency range
330 GHz to 500 GHz
Connector type
WM-570
Calibration standards
without sliding match

R&S®ZCWM-380

Order Number 1322.3101.02

Type
Waveguide Calibration Kit
Frequency range
500 GHz to 750 GHz
Connector type
WM-380
Calibration standards
without sliding match

R&S®ZCWM-250

Order Number 1322.3118.02

Type
Waveguide Calibration Kit
Frequency range
750 GHz to 1100 GHz
Connector type
WM-250
Calibration standards
without sliding match

Request information

Do you have questions or need additional information? Simply fill out this form and we will get right back to you.

Licença de marketing

O seu pedido foi submetido. Iremos contactá-lo em breve.
An error is occurred, please try it again later.
Informações gerais e legais

Manufacturer's recommended retail price (MSRP). The price shown does not include VAT. Prices and offers are only intended for entrepreneurs and not for private end consumers.

You may use the electronic signature via DocuSign to submit your information to enroll with the Rohde & Schwarz Customer Delegated Administration program. DocuSign processes the information provided according to their . The minimum system requirements for using the DocuSign system may change over time. The current system requirements are found

Termos e condições do sorteio de prêmios: 10 anos dos osciloscópios da Rohde & Schwarz

1. O sorteio de prêmios “10 anos dos osciloscópios da Rohde & Schwarz” (no presente, referido como “Sorteio”) é organizado pela Rohde & Schwarz GmbH & Co. KG, Mühldorfstraße 15, 81671 Munique, Alemanha, tel. +49 89 41 29 0 (doravante referida como “R&S”).

2. Todos os participantes podem se inscrever durante o período de 1º de janeiro de 2020 a 31 de dezembro de 2020, informando seu nome, nome da empresa e e-mail comercial.

3. A participação é gratuita e não depende da compra de mercadorias ou serviços.

4. O sorteio está aberto somente a pessoas jurídicas e apenas às pessoas jurídicas que possam ganhar os prêmios. Pessoas físicas não poderão participar em nome e interesse próprios, mas como representantes de uma pessoa jurídica, devendo preencher a ficha de participação em nome e segundo o interesse da pessoa jurídica.

5. Os prêmios a serem entregues são 1 de 10 R&S®RTB2000, no período de 1º de janeiro de 2020 a 31 de dezembro de 2020:

Prêmio: 1 osciloscópio digital R&S®RTB2000

6. O sorteio ocorrerá na sede da R&S, em Munique, à Muehldorstrasse 15, 81671. O ganhador dos prêmios será avisado por e-mail no prazo de cinco (5) dias úteis.

7. O representante autorizado da pessoa jurídica informará à R&S sobre a aceitação do preço. Caso a aceitação seja negada ou se não houver resposta em até duas (2) semanas, um novo ganhador será sorteado. Se não for possível definir um ganhador no prazo de quatro (4) semanas, o sorteio se encerrará e o prêmio prescreverá.

8. Aos funcionários da R&S e seus familiares, bem como às pessoas familiarizadas com o processo do sorteio e seus familiares, é vetado o preenchimento da ficha de participação.

9. Não são permitidos equivalente em dinheiro ou troca de prêmios. Os prêmios são intransferíveis. Todos os impostos, tributos, encargos, taxas e outras cobranças tributáveis no país do participante serão arcadas pelo participante.

10. Dados pessoais somente serão processados para os fins deste sorteio e excluídos quatro (4) semanas após o sorteio, se não acordado de outro modo.

11. O participante que não cumprir os presentes Termos e Condições estará sujeito à desclassificação pela R&S da participação neste concurso. Neste caso, os prêmios também poderão ser retirados retroativamente. Se um prêmio estiver sujeito à retirada retrospectiva por motivo de incumprimento dos presentes Termos e Condições, ele deverá ser devolvido pelo respectivo participante, às suas expensas, para o endereço da R&S mencionado na disposição N.1, e um novo ganhador será sorteado.

12. Os participantes não podem reivindicar os prêmios do sorteio e não são autorizados recursos legais neste sentido.

13. O sorteio e a relação contratual decorrente, entre a R&S e o respectivo participante, serão regidos e interpretados de acordo com as leis da Alemanha, sem dar efeito ao princípio do conflito de leis. Os tribunais de Munique, Alemanha, gozarão de jurisdição exclusiva em caso de disputa decorrente, direta ou indiretamente, da participação neste concurso.

* “fast delivery” inside 7 working days applies to the Rohde & Schwarz in-house procedures from order processing through to available ex-factory to ship.