Key facts
The ZES ZIMMER LMG600 precision power analyzer series provides high-accuracy power measurements in demanding test applications. DualPath architecture enables simultaneous wideband and narrowband analysis up to 10 MHz. The analyzer precisely measures very low power, complex multi-phase and high-power systems with configurable power channels and external sensors.
A 10.1" touchscreen with intuitive user interface, built-in data logging and customizable menus simplifies operation and reduces setup times. Whether in R&D, validation or certification, the analyzer delivers consistent, traceable results for accurate power analysis.
Tailored precision where you need it
Not every measurement in a setup demands the same precision or bandwidth. The LMG600 series supports four channel types (S, A, B, C) that can be mixed freely within the same chassis, ranging from the S-Channel with 0.015% AC accuracy and 10 MHz bandwidth down to the C-Channel for lower-frequency tasks. You configure the instrument to match the application — no over-specification, no compromises where it counts.
Channel flexibility
Wideband and narrowband values in a single measurement
Conventional power analyzers demand a compromise: enable anti-aliasing filter and lose wideband content, or disable it and risk aliasing errors in your FFT. The LMG600 series resolves the problem with two independent A/D converters per channel — one for the filterless wideband signal, one for the narrowband signal after anti-aliasing. Both paths run in parallel, delivering RMS values, harmonics, and FFT results from the same signal simultaneously.
DualPath architecture
A user interface tailored to your application
Build application-specific views from the ground up: choose electrical quantities and I/O variables for display, arrange them freely on screen and add graphical elements such as wiring diagrams, photographs or your brand identity. Pass/fail indicators and on-screen input fields for DUT-specific parameters can be embedded directly into the view, creating a measurement environment that even less experienced operators can use confidently.
Menu possibilities
Range extension of current measurements
Connected precision current transducers (PCT) use an integrated bus to notify the LMG600, automatically transferring scaling factors, delay compensation, sensor type and the last calibration date. LMG600 series power analyzers also directly supply power to sensors, eliminating need for separate supplies. There is no difference between direct and sensor-based measurements and no manual fine-tuning is required for accurate results.
PCT sensor and interconnections
Bridging power analysis and the automotive world
The LMG600 series can share up to 128 measured values and variables directly over the CAN bus including voltage, current, power, speed, torque, temperature and more. The interface is bidirectional: the LMG600 can also act on incoming CAN messages, with up to 128 trigger conditions available to start recordings, switch ranges or initiate logging based on external events. No middleware, no manual data alignment.
CAN menu LMG600
End-to-end standard conformance evaluation
The LMG test suite guides the LMG600 through EMC compliance tests in line with - IEC/EN 61000-3-2/-12 (harmonics) - IEC/EN 61000-3-3/-11 (flicker) - EN 50564/IEC 62301 (standby power). It works online or offline with any standard-compliant AC source and exports comprehensive test reports that include all traceability information. Upcoming changes are incorporated as they are adopted.
LMG test suite
Mechanical and environmental data, perfectly synchronized
The optional PSI adds fast analog inputs, switching inputs and outputs, torque/speed/frequency inputs and 32 analog outputs — all synchronized with the power channels. Torque, speed, temperature and pressure can be acquired alongside voltage and current. External devices can be triggered or driven directly from measured values.
No need to stop at seven channels
Multiple LMG600 units can be linked via sync cable to form a single virtual analyzer, automatically aligning cycle timing, system time, transient trigger events and the state of energy integration. Whether you need eight channels or more, the measurement will remain coherent across all chassis with no manual reconciliation required.
From microamps to 32 amps without changing ranges
IEC 62301 and EN 50564 compliance procedures require uninterrupted observation across a wide variety of load conditions. The LMG600 series has a continuous dynamic range of 500 µA to 32 A and 3 mV to 1000 V, with 18-bit resolution and a 10 ms minimum cycle time. Standby and full-load conditions can be characterized in a single, uninterrupted run, with 0.015% basic accuracy preserved even near the bottom of a range.
Order number 1603.5970.02
Order number 1603.0049.02
Order number 1603.5905.02
Order number 1603.0003.02
Order number 1603.5892.02
Order number 1603.5886.02
| Electrical specifications | ||
| Analog bandwidth | S channel | DC to 10 MHz |
| A channel | DC to 10 MHz | |
| B channel | DC to 500 kHz | |
| C channel | DC to 10 kHz | |
| Best power accuracy | S channel | 0.015% + 0.01% |
| A channel | 0.015% + 0.01% | |
| B channel | 0.05% + 0.02% | |
| C channel | 0.03% + 0.01% | |
| Maximum input voltage | Direct connection | 1000 V |
| Maximum input current | Direct connection | 32 A |
| Voltage range extension | S channel | 1500 VDC |
| Maximum sampling rate | 1.21 MS/s | |
| Voltage input impedance | 2.69 MΩ || 4 pF | |
| Earth capacitance | 90 pF | |
| Measured voltage rating | 300 V CAT IV, 600 V CAT III, 1000 V CAT II, 1500 V DC | |
| Protection against earth | From input to PE | 300 V CAT IV, 600 V CAT III, 1000 V CAT II |
| DC optimized | S channel | ● |
| Display and interfaces | ||
| Display | LMG611, LMG641 | 7" Touchscreen |
| LMG671 | 10.1" touchscreen | |
| Remote control interfaces | USB, LAN, RS-232 | |
| Additional inputs/outputs | ||
| Fast analog inputs | 2 inputs, 150 kS/s, 16 bit, BNC | |
| Analog inputs | 8 inputs, 100 S/s, 16 bit, D-Sub:DE-09 | |
| Analog outputs | 32 outputs, output per cycle, 14 bit, D-Sub: DA-15 & DB-25 | |
| Switching outputs | 8 outputs: 6 switches with 2 connections each and 2 switching outputs with common negative, D-Sub: DB-25 | |
| Switching inputs | 8 inputs: 150 kS / s, in two groups 4 inputs each with common ground, D-Sub: DB-25 | |
| Speed/torque/frequency inputs | 150 kS/s, D-Sub: DA-15 | |
| Special functions | ||
| Scope function | Graphical display of sample values over time in two scopes with 8 signals each | |
| Plot function | Two time (trend) diagrams of max. 8 parameters each, max. resolution 10 ms | |
| Star-delta conversion | LMG641, LMG671, LMG671-ATE | Conversion of line voltages to phase voltages and computation of resulting active power |
| Harmonics | Up to 2,000th order | |
| Flicker | According to IEC EN 61000-4-15 | |
| LMG test suite | Conformity tests in line with: IEC EN 61000-3-2 & 61000-3-12 for harmonics IEC EN 61000-3-3 & 61000-3-11 for flicker IEC 62301 & EN 50564 for standby power |
|
| General data | ||
| Dimensions (W x H x D) | LMG611 | 433 mm x 177 mm x 200 mm |
| LMG641 | 284 mm x 177 mm x 590 mm | |
| LMG671 | 433 mm x 177 mm x 590 mm | |
| LMG671-ATE | 84 HP x 4 RU x 590 mm | |
| Weight | LMG611 | Max. 7.2 kg |
| LMG641 | Max. 15.5 kg | |
| LMG671, LMG671-ATE | Max. 18.5 kg | |
| Rated mains voltage and frequency range | 100 v to 230 V, 47 to 63 Hz | |
| Rated power | LMG611, LMG641 | Max. 200 W |
| LMG671, LMG671-ATE | Max. 400 W | |
Order number 1603.5934.02
S-Channel for high-precision wideband measurements
Supports DualPath. DC-Optimized.
Bandwidth: DC - 10 MHz
Best power accuracy: 0.015 % + 0.01 %
Resolution: 18 bit
Order number 1603.0132.02
A-Channel for high-precision wideband measurements
Supports DualPath.
Bandwidth: DC - 10 MHz
Best power accuracy: 0.015 % + 0.01 %
Resolution: 18 bit
Order number 1603.5911.02
B-Channel for universal measurement applications
Supports DualPath.
Bandwidth: DC - 500 kHz
Best power accuracy: 0.05 % + 0.02 %
Resolution: 16 bit
Order number 1603.5928.02
C-Channel for high-precision measurements
Bandwidth: DC - 10 kHz
Best power accuracy: 0.03 % + 0.01 %
Resolution: 16 bit
Order number 1603.1097.02
Voltage range extension to 1500 V DC for S-Channel (L60-CH-S3)
Order number 1603.0110.02
Process Signal Interface
8 digital inputs, 8 digital outputs, 2 fast analog inputs (150 kS/s, 15 kHz), 8 slow analog inputs, 32 analog outputs, 2 frequency inputs (freq., or., pos.; DTL, HTL or diff.)
Order number 1603.1200.02
Sample Value Analysis Module
Software for continuous and gapless streaming of sample values on 16 tracks at a rate of 10 kS/s (up to 1.2 MS/s under optimal conditions).
Order number 1603.0890.02
Smart Vision
Smart add-on functions for the convenient evaluation of measurements
Order number 1603.0878.02
Harmonic analysis of U, I, P, Q and S
Up to 1000 Harmonics in the instrument, up to 2000 Harmonics via interface
Order number 1603.0861.02
Flicker meter according to EN61000-4-15
Order number 1603.0855.02
Event Triggering
Triggering on crossing voltage or current thresholds recording of 16 tracks with up to 16 million values each
Order number 1603.0826.02
Star-Delta-Conversion
Minimum requirement LMG600 with at least 3 power channels of the same type
Order number 1603.1251.02
Option Package CE Standby Power
LMG Test Suite for measurement standby power and creation of the standard-compliant documentation underlying Directive 2008/28/EC (former 2005/32/EC) or IEC 62301 or EN 50564
Order number 1603.1239.02
Option Package CE Harmonics
LMG Test Suite for analysis of measured values according to EN61000-3-2 and EN61000-3-12 for 1-phase and 3-phase equipment under test
Order number 1603.1222.02
Option Package CE Flicker
LMG Test Suite for analysis of measured values according to EN61000-3-3 and EN61000-3-11 for 1-phase and 3-phase equipment under test
Order number 1603.1900.02
Precision Current Transducer 600 Arms
Max. Bandwidth: 500 kHz
Best accuracy: ±0.0015%
Nominal DC current: ±900 A
Order number 1603.1880.02
Precision Current Transducer 200 Arms
Max. Bandwidth: 1 MHz
Best accuracy: ±0.0035%
Nominal DC current: ±300 A
Order number 1603.1874.02
Precision Current Transducer 1200 Arms
Max. Bandwidth: 400 kHz
Best accuracy: ±0.0015%
Nominal DC current: ±1500 A
Order number 1603.1897.02
Precision Current Transducer 2000 Arms
Max. Bandwidth: 300 kHz
Best accuracy: ±0.0007%
Nominal DC current: ±3000 A
Order number 1603.1845.02
2 m D-SUB interconnection cable for PCT Sensors
Order number 1603.1922.02
Power Supply Unit for up to 4 PCT Sensors
4-channel system interface unit for ultra-stable, high precision fluxgate PCT Sensors. Powers up to 4 PCTs at the same time.
Compact 19" design with 1HU.
Order number 1603.1951.02
PCT Connecting Cable
Length: 2.5 m
Adapter L60-X-ADSE required for connection to LMG600 Series.
Order number 1603.1100.02
Adapter for LMG600 Series to PCT Sensors
Order number 1603.0849.02
CAN bus interface
Bidirectional CAN bus connectivity according to ISO 11898-2 (high-speed CAN)
Order number 1603.0903.02
DVI Interface
For connection of an external display, beamer, touch device
Order number 1603.1122.02
19 inch rack mount kit for LMG641
Order number 1603.1145.02
19 inch rack mount kit for LMG671
Order number 1603.1151.02
2 x Handles for LMG671
2 pcs. for front face, CNC milled and powder-coated
Order number 1603.1168.02
4 x Handles for LMG671
4 pcs. for front and back face, CNC milled and powder-coated
Order number 1603.0910.02
256 GB Mass Storage Device for Measurement Results
Internal mass storage device for long-time recording of measurements.
Related products
