The R&S®Spectrum Rider FPH – handheld spectrum analyzer, frequency range from 5 kHz up to 44 GHz.

The R&S®ELEKTRA EMC test software controls EMC test systems and automates measurements for EUTs being certified for emissions (EMI) and immunity (EMS).

High-end EMI test receiver for compliance testing.

PC-offline software for R&S MXO series oscilloscope

R&S®MXO 4 SERIES OSCILLOSCOPE Next generation oscilloscope for accelerated insight

R&S®MXO 5C SERIES OSCILLOSCOPE Next generation oscilloscope in a compact form

R&S®MXO 5 SERIES OSCILLOSCOPE Next generation oscilloscope: evolved for more challenges

AN for measuring disturbance voltage in low-impedance power supply networks

Current probe for disturbance current and current injection measurements in the frequency range 20 Hz to 100 (245) MHz.

The evolution of preamplifiers

The B1000 complements the R&S®ESW for wideband EMI testing.

AMN for disturbance voltage measurements on single-phase EUTs

AMN for disturbance voltage measurements on high current lines

AMN for disturbance voltage measurements on three-phase EUTs

Disturbance voltage measurements in the frequency range 9 kHz to 30 MHz

Explore powerful R&S®EMC near field probes for the frequency range from 30 MHz to 3 GHz from test and measurement expert Rohde & Schwarz. Explore now.

The pulse limiter protects the measuring receiver's input against high-energy interference pulses.

EMI test receiver for quick, precise and compliant EMI measurements up to 7.125 GHz

The R&S®ESR is a midrange EMI test receiver for fast and reliable compliance testing.

R&S®MXO 3 SERIES OSCILLOSCOPE Next generation oscilloscope: Fast. Precise. Compact.

ZN-Z15x automatic economy calibration units series up to 8.5 GHz: 2, 4 or 6 ports SMA(f), ZN-Z154 up to 24 ports, 2-port type N(f). ZN-Z156: 2 ports 67 GHz.

The R&S®TS-PIO2 analog and digital I/O module is a 16-channel stimulus and a 16-channel parametric measurement unit for versatile DUT testing. It is part of the R&S®TSVP modular test and measurement platform and makes full use of the common analog measurement bus and the standardized isolated frontend technology. The required floating R&S®TS-PDC rear I/O DC supply module is included in the R&S®TS-PIO2.

Turnkey over-the-air (OTA) solution for antenna, cellular and non-cellular testing.

The R&S®FSWP phase noise analyzer combines low‑noise internal sources and real-time cross‑correlation for high sensitivity phase noise measurements.

R&S®5G site testing solution: automatic detection and demodulation of 5G NR and LTE signals. No parameter settings necessary.

The R&S®SAM100 system amplifier - an ultra-broadband solid state microwave amplifier with outstanding linearity and very good noise characteristics in frequency range from 2 GHz to 20 GHz.

The R&S®BBA300 is a robust, compact, ultra-wide band amplifier for use in critical test environments such as EMC, product validation and OTA coexistence in the frequency range of 380 MHz to 18 GHz and RF output power up to 300 W P1dB.

The FFT-based spectrum analysis function can be used to measure a DUT's spurious and harmonics, providing short sweep times along with high dynamic range and fine frequency resolution. It quickly detects undesired signal components (spurious) in converters and T/R modules. The marker-to-spectrumfunction directly gets to the root of problems in the event of unexpected S-parameter results, thus providing fast and extremely useful integrated diagnostics.

VNA Source Phase Control Options for characterization of devices requiring a defined phase such as differential amplifiers, mixers, IQ mixers and others.

There are several reasons to characterize RF components under pulsed conditions. Often it is to prevent thermal damage to the device under test or to characterize it under operating conditions. Vector Network Analyzers offer integrated hardware and software for accurate device characterization under pulsed conditions. This hardware includes built-in pulse modulators, pulse generators and synchronization IO including for external device control.