Wireless coexistence testing is crucial for transmitters and receivers that operate in close proximity or on the same chip or module (in-device).

Describes the specific functions of the application, including the remote control commands with programming examples.

Bluetooth® is the established wireless communications technology for the short range, facilitating both voice and data transmission to create a personal area network.

Describes the specific functions of the application, including the remote control commands with programming examples.

23-May-2024 | Press Releases | EMC testing

Designed for test environments, the BBA300 amplifier offers up to 450 W RF saturation power at the output, at frequencies from 380 MHz to 6 GHz.

Describes the specific functions of the application, including the remote control commands with programming examples.

To ensure connectivity and trouble-free operation, each Bluetooth® enabled device has to be tested for conformance with Bluetooth SIG standards and regulatory requirements.

23-Nov-2017

Describes the specific functions of the application, including the remote control commands with programming examples.

This document describes Bluetooth Low Energy RF over-the-air RX and TX measurements using advertising channels for communication with Bluetooth Low Energy devices.

14-Dec-2020 | AN-No. 1C109

This application note describes how to use the R&S CMW platform to perform the measurements defined in Bluetooth test specification version 5.

19-Jun-2017 | AN-No. 1MA282

This document describes the direct test mode mechanisms for testing Bluetooth Low Energy devices and explains how the direct test mode connection is established. The R&S CMW uses a USB port for the direct test mode connection while the Equipment under Test (EUT) may provide a USB port, a serial port or even a 2-wire UART interface for this purpose. Installing or assigning the right driver for the EUT is the main configuration task on the R&S CMW. For EUTs with USB port, the R&S CMW provides a Bluetooth Low Energy USB driver which has to be assigned to the connected EUT.

14-Dec-2016 | AN-No. 1C105

Guide to adaptive frequency hopping for improved Bluetooth® BR/EDR signaling performance

14-Dec-2016 | AN-No. 1C108

Bluetooth

05-Jun-2019 | AN-No. 1MA108

The R&S®CMW wireless communication tester are ideal for designing and verifying Bluetooth® Low Energy (LE) circuits and modules.

27-Jan-2017

Transmitter and Receiver Measurements on Bluetooth Modules with CMU200

06-Aug-2001 | AN-No. 1MA46

Smartly verify and decode Bluetooth® Low Energy (BLE) transmit signals with a reliable and costefficient spectrum analyzer – the R&S®FPC.

17-May-2018

Rohde & Schwarz test solutions for verifying the performance of automotive Bluetooth connectivity including audio quality, A2DP and phone book transfer.

Bluetooth Transmitter Measurements without Connection Setup

04-Feb-2003 | AN-No. 1MA49

This webinar will give an overview of the latest Bluetooth LE developments and demonstrate related test solutions.

This webinar will give an overview of the latest Bluetooth LE developments and demonstrate related test solutions.

The Rohde & Schwarz Bluetooth RF test solution with the R&S CMW and R&S CMWrun is closely aligned to the Bluetooth RF Test Suite. This document describes common setups for these tests and the required configurations.

04-May-2015 | AN-No. 1MA261

Bluetooth 5.2 and Bluetooth Low Energy Audio Overview

Understand the challenges of testing wireless connectivity technologies and learn all about the latest specifications and testing applications for Wi-Fi, UWB and Bluetooth®.

The R&S CMW platform covers all test cases defined by Bluetooth SIG. Bluetooth 5 testing, CMW test platform The video demonstrates Bluetooth 5 measurements using the R&S CMW270 wireless connectivity tester.

This poster identifies the most prominent vehicle features and itemizes their associated wireless standards such as UWB, 5G, BluetoothTM and DAB. Furthermore, each feature is classified into logical categories, eg infotainment, automated driving and monitoring.

Rohde Schwarz, R&S, Let’s talk IoT, IoT, Bluetooth LE, BLE testing, Bluetooth LE test mode, BT BER test This video explains different way of testing Bluetooth® Low Energy. The BLE test mode supports all tests in direct test mode (DTM) without the need of a control cable.

Generating Bluetooth RF Test Signals with SMIQ Signal Generator

30-Jan-2001 | AN-No. 1MA31

This application note describes the tests performed with additional equipment and presents straightforward solutions based on the R&S®CBTgo software.

18-Jul-2013 | AN-No. 1MA200

Describes the specific functions of the application, including the remote control commands with programming examples.

Video, Application video, Product video CMW500, CMW Platform, CMW270, CMW290, Bluetooth, Low Energy, Bluetooth LE measurement This video shows how to measure Bluetooth Low Energy (LE) devices with the R&S®CMW test platform