| Interface |
| Control bus |
|
|
CompactPCI/PXI |
| DUT connector (front) |
|
|
DIN 41612, 96 pins |
| Rear I/O connector |
|
|
CompactPCI, 110 pins |
|
Signal generation
|
| Output resolution |
|
|
16 bit |
| Number of analog channels |
fully independent or synchronous, differential,
floating, cascadable, short-circuit-proof |
|
2 |
| Digital marker channels |
one per channel |
|
2 TTL |
| Memory (RAM) |
|
|
1 Msample per channel |
|
Signal output modes
|
| DC mode |
|
|
static value |
| Sinewave |
|
|
1 Hz to 1 MHz (max.) |
| Triangle, ramp |
|
|
1 Hz to 1 MHz (max.) |
| Squarewave |
|
|
1 Hz to 1 MHz (max.) |
| Pulse (high – low) |
|
|
1 % to 99 % (min. pulse width 500 ns) |
| Arbitrary waveforms in burst mode |
sample rate |
|
DC, 1 sample/s to 25 Msample/s |
| |
waveform length |
|
1 to 1048576 (1 M) points per channel
if sample rate = 25 Msample/s: 18 to 1048576 (1 M) points per channel |
| |
resolution |
|
40 ns (min.) |
| |
chaining of sequences |
|
256 per channel, max. 16 382 cycles per segment |
|
Timing control
|
| Continuous mode |
frequency |
|
1Hz to1 MHz |
| |
resolution |
|
0.004 % of setting |
| |
accuracy |
|
±(resolution + reference clock accuracy) |
| Reference clock |
|
|
PXI clock of R&S®TS-PCA3, 10 MHz,
±(1.5 ppm + 1 ppm/year) |
|
Output voltage
|
|
|
amplitude range |
| Output mode |
|
|
output voltage (max.) |
| Single channel, GND referenced |
|
|
±20 V, ±10 V, ±5 V, ±1 V |
| Single channel, floating |
|
|
±20 V, ±10 V, ±5 V, ±1 V |
| Cascaded channels |
|
|
±40 V, ±20 V, ±10 V, ±2 V |
|
Output current
|
max. load current, depending on frequency |
| Output mode |
f ≤ 300 kHz |
300 kHz ≤ f ≤ 500 kHz |
500 kHz ≤ f ≤ 1 MHz |
| Single channel, GND referenced |
250 mA |
250 mA |
125 mA |
| |
250 mA |
250 mA |
125 mA |
|
|
250 mA |
125 mA |
50 mA |
|
Amplitude accuracy (no load)
|
1 Hz to 100 kHz |
|
100 kHz to 1 MHz |
| Range |
Resolution |
Error limits |
Error limits |
| 20 V |
0.6 mV |
±0.25 dB |
±0.5 dB |
| 10 V |
0.3 mV |
±0.25 dB |
±0.5 dB |
| 5 V |
0.15 mV |
±0.3 dB |
±0.5 dB |
| 1 V |
0.03 mV |
±0.3 dB |
±0.5 dB |
| Temperature coefficient for amplitude |
|
|
0 % to –0.05 %/°C of range |
| Offset range |
|
|
–20 V to +20 V (offset + amplitude less than
amplitude
range limits) |
| Offset resolution |
|
|
12 bit |
|
DC offset accuracy (no load)
|
| Range |
Resolution |
|
Error limits |
| ±20 V |
10 mV |
|
±(0.5 % + 100 mV) |
| ±10 V |
2 mV |
|
±(0.5 % + 80 mV) |
| ±1 V |
0.5 mV |
|
±(0.5 % + 20 mV) |
| Temperature coefficient DC offset |
|
|
0 % to –0.04 %/°C of range |
| Source impedance |
|
|
< 2.5 Ω, 1.25 Ω (typ.) |
| Output coupling |
|
|
DC |
| Bandwidth with lowpass filter (3 dB) |
|
|
3 MHz/100 kHz/3 kHz
(programmable for arbitrary mode) |
| Crosstalk (typ.) |
|
|
–70 dB at 100 kHz, –60 dB at 1 MHz |
|
Spectral purity (sinewave)
|
| Harmonic distortion, frequency range 20 Hz ≤ f ≤ 50 kHz |
|
|
|
| Output Vpp |
|
|
Harmonic distortion (typ.) |
| ≤ 200 mV |
|
|
< –70 dBc |
| ≤ 2 V |
|
|
< –65 dBc |
| ≤ 20 V |
|
|
< –48 dBc |
| ≤ 40 V |
|
|
< –40 dBc |
|
Synchronization, per channel
|
| Trigger inputs |
|
|
1 × local trigger (TTL),
8 × PXI trigger bus |
| Slope |
|
|
positive/negative |
| Pattern |
|
|
9 bit, 3 states: high, low, don’t care |
| Delay |
|
|
40 ns to 100 s |
| Trigger outputs |
|
|
1 × local trigger (TTL), programmable
marker synchronous with analog signal;
8 × PXI trigger bus; marker channels
may be used as separate digital channels |
|
Analog measurement bus and relay multiplexer
|
| R&S®CompactTSVP analog measurement bus |
|
|
8 lines |
| Relay scanner (per channel) |
|
|
two pole × 8-to-1 multiplexer to local
analog bus |
| Coupling relays |
|
|
8, local bus to global analog bus |
| Switching voltage |
|
|
125 V DC/90 V RMS (max.) |
| Switching current |
|
|
1.0 A (max.) |
| Switching power DC/RMS |
|
|
10 W/10 VA (max.) |
| Isolation (channel-to-channel, channel-to-earth) |
|
|
125 V |
|
General data
|
| Power consumption |
|
|
+5 V/3.0 A (typ.) |
| |
|
|
≥ 8.5 A (max.) |
| |
|
|
+3.3 V/1.3 A |
| |
incl. R&S®TS-PDC |
|
47 W (max.) |
| Environmental conditions |
| Temperature |
operating temperature range |
|
+5 °C to +40 °C |
| |
storage temperature range |
|
–10 °C to +60 °C |
| Damp heat |
|
|
+40 °C, 80 % rel. humidity, steady state,
in line with EN 60068-2-30 |
|
Mechanical resistance
|
| Vibration |
sinusoidal |
|
5 Hz to 55 Hz, 0.15 mm amplitude const.,
55 Hz to 150 Hz, 0.5 g const.,
in line with EN 60068-2-6 |
| |
random |
|
10 Hz to 300 Hz, acceleration 1.2 g (RMS),
in line with EN 60068-2-64 |
| Shock |
|
|
40 g shock spectrum, in line with MIL-STD-810E,
method 516.4, procedure I |
|
Product conformity
|
| Electromagnetic compatibility |
EU: in line with EMC Directive 2004/108/EC |
|
applied harmonized standards:
EN 61326-1 (industrial environment),
EN 61326-2-1,
EN 55011 (class A),
EN 61000-3-2,
EN 61000-3-3 |
| Electrical safety |
EU: in line with
Low Voltage Directive 2006/95/EC |
|
applied harmonized standard:
EN 61010-1 |
| Dimensions |
W × H × D |
|
20 mm × 174 mm × 316 mm
(0.79 in × 6.85 in × 12.44 in) |
| Weight |
|
|
0.5 kg (1.1 lb) |
| |
incl. R&S®TS-PDC |
|
0.8 kg (1.76 lb) |
| Recommended calibration interval |
|
|
12 months |
