Download Center

CMW290 - EU Declaration of Conformity

R&S®CMW290 - Fact sheet Brochures and Data Sheets

Rohde & Schwarz offers the R&S®CMW500 radio communication tester and the R&S®CMW290 functional radio communication tester to meet different testing needs; R&S®CMWcards for C-IoT

15-Oct-2018

Testing eSIM compliance and remote SIM provisioning

22-Aug-2019

Product safety certificate according to EN/IEC standards for CMW500, CMW290, CMW270

Product safety certificate according to CAN/CSA/UL standards for CMW500, CMW290, CMW270

DTMF analysis on CMW500 and CMW290

How to configure a external trigger at CMW500, CMW290, CMW270 to synchronize with LTE signal time frames

CMW500 / CMW290: GPRS / EDGE packet data measurements failed because UE stay not in TBF (Temporary Block Flow) state.

How can the CQI (Chanel Quality Identifier) from UE and coresponding 3GPP specified mapping to Modulation and TBS be tested?

If a CMWrun test plan script has been fished the AC power of a CMW500 / CMW290 / CMW270 should be shut down automaticly.

How to get Wireshark log files for IMS (VoLTE, VoWiFi) when using CMW500/CMW290

During the call setup with VoLTE/VoWiFi with EVS voice codec the bandwidth is negotiated. How can the bandwidth be setup and how will it be shown in the CMW user interface?

CMsquares download file not available in R&S Installation Manager

LTE UE capabilities Interpretation of Bandwidth Combination Set values shown in CMW Callbox

During a CMWrun test my DUT fails on delivering isolated measurements using CMW270/290/500.

Setting a CMW as a Bluetooth LE packet Generator

It is required to run two simultaneous NB IoT Signaling tests in parallel. Is this possible for a CMW call box tester?

How can the external attenuation values be configured and embedded in the CMWRun test sequences?

CMWrun Settings for external Interfer usage in Bluetooth LE Test Plans.

CMW500/290/270: No more WLAN signaling function after WLAN firmware update

How can a WiFi connection instead be made to a WiFi network for remote access of the CMW?

Is it possible to set up an IP peer to peer test using CMW500 between a corporate network and one EUT attached to an LTE cell?

The CMW500/2xx shows a resource conflict in this situation when using in parallel the RFxCOM port and the RFxOUT port of the same RF-frontend.

IEEE 802.11 Wireless LAN Testing with the R&S CMW Wideband Radio Communication Tester - Application Brochure

Installation of CMWcards is made on a external PC that should control the CMW mobile radio tester via LAN interface. But also the PC and the CMW are connected to the same LAN the remote connection do not work and the resource check showed "not connected".

MWC2019, CMW290, BLE, BT LE signaling, NB-IoT, IoT, GSMA, Mobile World Congress Rohde & Schwarz demonstrates combined RF and functional test for NB-IoT and Bluetooth® 5.0 LE signaling at GSMA Mobile World Congress 2019 in Barcelona.

This application note describes Battery Life Measurements with the R&S®RT-ZVC02/04 Multi-Channel Probe. The measurements are described with the use of an oscilloscope.

17-Jan-2019 | AN-No. 1TD07

Rohde Schwarz, R&S, IoT, secure communication, CMW500, CMW290 Let’s talk IoT – Testing the secure communication behavior of IoT devices

Video, Application video, Product video CMW500, CMW Platform, CMW270, CMW290, Bluetooth, Low Energy, Bluetooth LE measurement This video shows how to measure Bluetooth Low Energy (LE) devices with the R&S®CMW test platform