Rohde & Schwarz solutions for power integrity testing

Power integrity testing

Solutions for power integrity testing

Stable and clean power rail signals are the basis for reliable performance of electronic devices. Power rail voltages are getting smaller and tolerances are decreasing, making it much more difficult to accurately measure power rails. In the past, any oscilloscope could measure ripple on standard 5 V rails with 10% tolerance because the 500 mV requirement was well above the noise level of the scope. In contrast, the new requirements are challenging for power rail measurements. Performing an accurate ripple measurement on a 1 V rail with 2 % tolerance, for example, is difficult on most oscilloscopes. Rohde & Schwarz oscilloscopes support these tasks with a variety of accessories and analysis functions.

Active, low-noise power rail probe
Active, low-noise power rail probe

Power integrity probing

The active R&S®RT-ZPR20 and R&S®RT-ZPR40 power rail probes are designed to measure small AC characteristics of DC rails. They only add about 10 % to the noise of the oscilloscope and provide a built-in offset of ±60 V, making it possible to exploit the maximum oscilloscope vertical sensitivity for lower noise and more of the scope’s ADC bits. In combination with Rohde & Schwarz oscilloscopes, it is an ideal solution for fast and accurate power integrity measurements.

Measuring ripple on a 1.2 V DDR4 power supply
Measuring ripple on a 1.2 V DDR4 power supply

Verifying power integrity for DDR memories

Ripple and noise on the power distribution network negatively impact clock and data jitter of embedded devices that use DDR memory. This directly affects data transfer performance. The power supply voltages of embedded designs with DDR memories therefore need to be qualified for reliable operation. Whereas DDR3 memories tolerated 75 mV (Vpp) ripple, this tolerance decreased to only 60 mV (Vpp) for DDR4 memories. Most likely, it will decrease further in the future. This requires low-noise measurement solutions for power integrity testing.

Five tips for power integrity measurements
Five tips for power integrity measurements

Five tips for power integrity measurements

Challenging power integrity measurements can be performed quickly and accurately with this helpful guide

Power rail measurements are necessary to meet the decreasing tolerances for power voltages of modern electronic devices. Such tests require the right equipment as well as a few tricks to obtain the best measurement result. This guide helps you find the right oscilloscope, probing solution and measurement settings for reliable power integrity testing.
Register now and read our free guide.

Power integrity debugging

Video: Power integrity debugging

Learn more about Rohde & Schwarz solution for power integrity testing in this video.

Related products


Intuitive, high-performance lab oscilloscope with excellent fidelity, a responsiveness of 1 million waveforms/s and up to 16 bit vertical resolution. It enables quick and accurate power integrity testing with high confidence and user friendliness.

Product information


This fully integrated multi-domain oscilloscope supports power rail analysis with high accuracy. Optimized for embedded design and general debugging, it allows you to accomplish everyday T&M challenges quickly, accurately and easily.

Product information


High bandwidth and sensitivity, very low noise and extra-large offset compensation make the R&S®RT-ZPR20/40 power rail probes excellent probes for power integrity measurements. An integrated highly accurate DC voltmeter provides direct DC voltage readout.

Product information

Related topics

Efficiency testing

More information

EMI debugging of embedded power electronics designs

More information

Verification and debugging

More information

Request information

Do you have questions or need additional information? Simply fill out this form and we will get right back to you.

I want to receive information from Rohde & Schwarz via

Marketing permission

What does this mean in detail?

I agree that Rohde & Schwarz GmbH & Co. KG and the Rohde & Schwarz entity or subsidiary company mentioned in the imprint of this website, may contact me via the chosen channel (email or postal mail) for marketing and advertising purposes (e.g. information on special offers and discount promotions) related to, but not limited to, products and solutions in the fields of test and measurement, secure communications, monitoring and network testing, broadcast and media, and cybersecurity.

Your rights

This declaration of consent may be withdrawn at any time by sending an email with the subject "Unsubscribe" to Additionally, a link to unsubscribe from future email advertisements is contained in each email sent. Further details on the use of personal data and the withdrawal procedure are set out in the Statement of Privacy.

Your request has been sent successfully. We will contact you shortly.
An error is occurred, please try it again later.