Centro de descargas

Describes the specific functions of the application, including the remote control commands with programming examples.

English - 13 nov 2025

Provides the information required to prepare the instrument for use and start working.

English - 22 sept 2025

Collection of user manuals for of all options supported by the simulation software R&S®WinIQSIM2 TM .

English - 13 nov 2025

The user manuals describe the digital standards supported by the signal generators R&S®SMU200A, R&S®SMATE200A, R&S®SMJ100A and R&S®AMU200A.

English - 28 ene 2016

The introduction of the transmission of compressed TV signals to MPEG2 and DVB for cable, satellite and terrestrial (COFDM) lead to the creation of many abbreviations that have to be explained to the “uninitiated”. In the previous three lines, three abbreviations whose meanings are not obvious have already been mentioned. A table explaining what these abbreviations mean is therefore essential.

English - 20 jul 2001

A large variety of measurements is performed in audio engineering in order to ensure transmission quality of analog and digital devices. An audio analyzer suitable for all these tasks will, therefore, incorporate a multitude of functions, resulting in a correspondingly large number of settings.This application note is to help test engineers using the R&S®UPP and R&S®UPV audio analyzers. It presents setting examples for all basic audio measurements to be performed immediately. For each setup, information is given on the type of measurement, the underlying standards, and on how to modify the graphic display results.

English - 7 jul 2014

Describes the specific functions of the application, as well as remote control commands and performance test.

English - 2 oct 1999

- not available -

English - 20 jul 2001

Describes all instrument functions and remote control commands, including measurement and programming examples, for the base unit.

English - 14 ene 2026

This application note is about creating your own battery model for the R&S®NGM200 and R&S®NGU201, beyond the standard models provided within the battery simulation option NGM-K106 and NGU-K106. To get to a battery model, a few steps are required. To determine the parameters for the battery model, it is necessary to discharge a battery using a selected method, to record the data and to calculate the model on this basis. With this software, a connection can be established to the instrument, batteries can be measured using various measurement methods, and a model can then be created from these measurements. These models, which are determined from the measurements, can then be simulated with the power supply, thus creating a digital twin of the battery. Using these, test scenarios can be carried out in a safe and reproducible environment.

English - 21 nov 2022

Describtion and explanation of the MPEG and DVB-Standards and TV T&M

English - 9 dic 2011

The R&S® Broadcast Test Center BTC supports the new “Next Generation Broadcast Standard ATSC 3.0” with BTC firmware version 2.20 and later.This application note describes the necessary settings in the user interface of the R&S® Broadcast Test Center BTC.

English - 27 mar 2018

Provides the information required to prepare the instrument for use and start working.

English - 22 sept 2025

Provides the information required to prepare the instrument for use and start working.

English - 28 ene 2016

Provides the information required to prepare the instrument for use and start working.

English - 28 ene 2016

Provides the information required to prepare the instrument for use and start working.

English - 28 ene 2016

When it comes to testing analog and digital TV and audio broadcast receivers in cars, special requirements must be met. Although suppliers ensure the receiver functionality, this functionality must be tested when the receiver is integrated into the car. When it comes to testing analog and digital TV and audio broadcast receivers in cars, special requirements must be met. Although suppliers guarantee the receiver functionality, this functionality must be tested when the receiver is integrated into the car.

English - 19 feb 2015

In high-speed digital measurement applications, test fixtures are commonly used to connect devices under test to measurement equipment. Characterization, and analysis in the time and frequency domains that accounts for various constraints helps to remove the influence of these fixtures.

English - 22 may 2023

Broadcasting transmitters are subject to particularly stringent standards with respect to broadcast signal quality, because even small faults can lead to service disruptions for many viewers. A single instrument, the R&S®ETL TV analyzer, performs all required ISDB-T transmitter measurements, from the initial acceptance testing for the transmitter, to measurements performed during commissioning and preventive maintenance.

English - 13 may 2013

For A/V devices such as smartphones, tablet PCs, Blu-ray players, set-top boxes and TV sets, the perceived video quality must satisfy very high standards. A/V devices need to hold their own in three main areas:ı Stability (environmental influences, response to source signal disturbances, etc.)ı Performance (switching times, delays)ı Compliance with standards (input and output formats)Any deviations from the expected video and audio output can be automatically and precisely detected with R&S A/V distortion analysis on all common analog and digital interfaces such as HDMI™ and MHL™.This document examines the relevant setups and configurations.

English - 15 oct 2014

Signal faults and anomalies can cause electrical and electronic systems to fail. Especially in the field, these errors can lead to system downtimes and produce high costs. Consequently, finding them quickly and efficiently as well as identifying their source are crucial.

English - 30 dic 2015

For the transmission of digial audio data, different data formats are in use. The AES/EBU format, which is used in professional applications, as well as the S/P DIF format used in consumer electronics, transmit the audio data in time multplex for both channels. Additonal bits in the data stream cover complementary information, respectively are used for error detection.The generation and the analysis of those protocol data using the audio analyzers UPD or UPL is the topic of this application note. An extract of the AES3 standard informs about the basic definitions.

English - 4 jun 1998

With the R&S®RTB2000/RTM3000/RTA4000 oscilloscopes, you control and interact remotely via LAN. These oscilloscopes incorporate the USB-based connectivity standard media transfer protocol (MTP).

English - 20 mar 2017

Broadcasting transmitters are subject to particularly stringent standards with respect to broadcast signal quality, because even small faults can lead to service disruptions for many viewers. A single instrument, the R&S®ETL TV analyzer, performs all required ATSC transmitter measurements, from the initial acceptance testing for the transmitter, to measurements performed during commis-sioning and preventive maintenance.

English - 13 may 2013

Broadcasting transmitters are subject to particularly stringent standards with respect to broadcast signal quality, because even small faults can lead to service disruptions for many viewers. A single instrument, the R&S®ETL TV analyzer, performs all required DVB-T / DVB-H transmitter measurements, from the initial acceptance testing for the transmitter, to measurements performed during commissioning and preventive maintenance.

English - 13 may 2013