Automotive for future mobility

Webinars and videos on future automotive mobility

Automotive webinars and videos – always well informed

In this section, you will find the relevant webinars and interesting facts about the following topics: eCall, RED, radar, ADAS, connected cars, future automotive trends.

If you wish to know what the future holds, keep on reading!

Watch our latest webinars

Webinar: Automotive radar test solutions using high-performance oscilloscopes

This webinar will demonstrate how to simultaneously measure and analyze up to four 4 GHz automotive radar signals at 79 GHz by using a Rohde & Schwarz oscilloscope as a phase coherent receiver and high precision mixers for downconversion.

Broadcasting date: July 9/10, 2019
Language: English
Duration: 28 min

More information

Webinar: Radio Equipment Directive (RED) and coexistence

The efficient use of spectrum is a key-requirement of the new radio equipment directive (RED). Not only transmitters, but also receivers now have to meet minimum regulatory requirements and need to be tested. This discussion with an EMC testing and regulatory expert goes through all relevant RED regulatory, testing and co-existing topics.

Broadcasting date: May 20, 2019
Language: English
Duration: 52 min

More information

Webinar: V2X – the building blocks of an intelligent transport system

Topic:
This webinar will take a look at the market requirements and the use cases that are driving the decisions about these technologies, trace the evolutionary path toward 5G and provide a picture of what is being discussed in each of the key regions.

Broadcasting date: April 9/10, 2019
Language: English
Duration: 43 min

More information

Webinar: Comprehensive radar integration testing

Topic:
This webinar will focus on the integration of radar sensors in future autonomous vehicles.

Broadcasting date: February 13/14, 2019
Language: English
Duration: 43 min

More information

Webinar: 1000BASE-T1 automotive Ethernet compliance testing

Topic:
This webinar will focus on 1000BASE-T1 automotive Ethernet compliance testing based on the Open Alliance (OA) TC8 specification for the physical layer.

Broadcasting date: January 22/23, 2019
Language: English
Duration: 37 min

More information

Webinar: eCall and its challenges. Leading the way to the next generation eCall system

Topic:
We will demonstrate a reliable and fast test solution for next generation eCall that helps in the development of eCall devices where in-band modem eCall and next generation eCall coexist.

Broadcasting date: November 7, 2018
Language: English
Duration: 55 min

More information

Watch more webinars

Webinar: Ready for RED – Part 3: Quasi Peak measurements on FM radios according to EN 303 345

In this webinar, you will learn how to setup the BTC (Broadcast Test Center) for FM signal generation according to EN 303 345 and how to perform Quasi Peak audio measurements for FM signals according to EN 303 345.

Jul 11, 2018

Webinar: Automotive Ethernet compliance testing

This webinar presents details on the individual test cases of the compliance test and provides useful information on the required test setup.

May 28, 2018

Webinar: Debugging automotive Ethernet using the trigger & decode

In this webinar we will show examples, such as how bus analysis via triggering and decoding helps in developing ECUs with automotive Ethernet interfaces.

May 08, 2018

Webinar: Ready for RED – Part 2: DAB car radio testing with the R&S®BTC

Learn how to perform audio measurements on a DAB car radio receiver for EN 303 345 compliance testing.

Nov 20, 2017

Webinar: Secure or not secure? Analysis of IP security mechanisms in IoT and mobile devices

This webinar provides the background to IP secure connections.

May 11, 2017

Webinar: Ready for RED - Part 1

In this webinar we explain how new mandatory standards affect the testing of car radio and TV entertainment systems or modules.

Mar 14, 2017

Webinar: Analysis of FMCW radar signals in automotive application

Increase your understanding of radar signal processing and waveforms.

Jul 07, 2014

Videos

eCall (emergency call)

eCall is a European initiative intended to bring rapid assistance to motorists involved in a collision anywhere in the European Union.

Aug 12, 2019

High-End GNSS simulation with the R&S®SMW200A - Episode 6

This video shows how to perform advanced interferer simulations for testing multi-antenna GNSS receivers with anti-jam capabilities, also known as Controlled Reception Pattern Antennas (CRPAs).

Apr 25, 2019

High-End GNSS simulation with the R&S®SMW200A - Episode 5

The performance of GNSS receivers must be validated and characterized not only under ideal conditions, but also in the presence of other communication signals like GSM, UTMS or LTE.

Apr 25, 2019

High-End GNSS simulation with the R&S®SMW200A - Episode 4

Unintentional or intentional interference can significantly impair the reception of GNSS signals.

Apr 25, 2019

Wideband signal analysis in the mmWave range presented at EuMW 2017

Rohde & Schwarz demonstrated 5 GHz signal analysis bandwidth at the European Microwave Week 2017 in Nuremberg.

Feb 15, 2019

1000BASE-T1 cable testing according to OPEN Alliance TC9

A guide to perform cable testing based on unshielded twisted pair (UTP) for 1000BASE-T1 based on the OPEN Alliance TC9 specification.

Jan 03, 2019

Powerful 100BASE-T1 decoding

Decoding details for 100BASE-T1 Automotive Ethernet using the R&S®RTO with K57 option.

Nov 28, 2018

Powerful 100BASE-T1 triggering

Triggering details for 100BASE-T1 Automotive Ethernet using the R&S®RTO with K57 option.

Nov 28, 2018

100BASE-T1 compliance testing - MDI return loss

A guide to carrying out a 100BASE-T1 compliance test for the MDI return loss using an R&S®ZND 2-port vector network analyser controlled by the ScopeSuite automation software.

Nov 28, 2018

Decoding automotive Ethernet and CAN using R&S scopes

A comparisson between CAN decoding on the R&S®RTM oscilloscope with automotive Ethernet decoding using the K57 option on the R&S®RTO oscilloscope.

Nov 28, 2018

1000BASE-T1 compliance testing - Test mode 6: Maximum output droop

A guide to carrying out a 1000BASE-T1 compliance tests with test mode 6 (maximum output droop test) on an R&S®RTO. The video gives an overview of how to configure the setup and generate test reports for further analysis

Oct 25, 2018

1000BASE-T1 compliance testing - Test mode 4: Transmitter distortion test with disturber

A guide to carrying out a 1000BASE-T1 compliance tests with test mode 4 (transmitter distortion test with disturber) on an R&S®RTO. The video gives an overview of how to configure the setup and generate test reports for further analysis.

Oct 25, 2018

1000BASE-T1 compliance testing - Test mode 5: Transmitter power spectral density (PSD), power level and peak differential output

A guide to carrying out a 1000BASE-T1 compliance tests with test mode 5 (transmitter power spectral density) on an R&S®RTO. The video gives an overview of how to configure the setup and generate test reports for further analysis.

Oct 25, 2018

1000BASE-T1 compliance testing - Test mode 2: MDI jitter and clock frequency

A guide to carrying out a 1000BASE-T1 compliance tests with test mode 2 (MDI jitter and clock frequency) on an R&S®RTO. The video gives an overview of how to configure the setup and generate test reports for further analysis.

Oct 25, 2018

EMI debugging

This video shows how the R&S®RTO oscilloscope can be used with a near field probe to find and fix EMI issues quickly and reliably during the development at the R&D lab thereby minimizing expensive re-testing and shortening time to market.

Jul 02, 2018

How to perform Bluetooth 5 testing with the R&S®CMW test platform

The video demonstrates Bluetooth 5 measurements using the R&S CMW270 wireless connectivity tester.

Jul 02, 2018

Radar applications: Radial velocity measurements - Video 1/2

In this first video, we start with a simple application such as distance and speed measurement. The basic setup for radar velocity tests is shown. The theory basics and formulas are explained. The video shows a test using a moving vehicle and how the data is evaluated using an oscilloscope.

Jul 02, 2018

Reliable all-in-one test solution for automotive radar sensors

Rohde & Schwarz demonstrated the all-in-one test solution for the production of automotive radar sensors at European Microwave Week 2017 in Nuremberg.

Jul 02, 2018

Radar applications: Radar range and velocity measurements - Video 2/2

In this video we show a powerful way to perform radial velocity and range measurements using Rohde & Schwarz instruments as well as signal processing software implemented in MATLAB.

Jul 02, 2018

Rohde & Schwarz - your partner in automotive testing

Managing increasingly complex electronic systems and industry standards such as automotive Ethernet create additional requirements for automotive testing, alongside security issues.

Jul 02, 2018

Triggering & decoding 100Base-T1 BroadR-Reach Ethernet

Triggering & decoding real-world OABR automotive Ethernet with an oscilloscope.

Jun 29, 2018

1000BASE-T1 compliance testing - Test mode 1

Guideline for 1000BASE-T1 compliance testing using the R&S®RTO and R&S®ZND.

Jun 28, 2018

100Base-T1 compliance testing

Guideline for 100Base-T1 compliance testing using the R&S®RTO and R&S®ZND.

Jun 01, 2018

High-End GNSS simulation with the R&S®SMW200A - Episode 3

In this third video of R&S’s new video series on high-end GNSS testing, it is shown how to set up a multi-constellation, multi-frequency GNSS scenario and feed the GNSS signals to a connected GNSS receiver.

Mar 19, 2018

High-End GNSS simulation with the R&S®SMW200A - Episode 2

In this second video of R&S’s new video series on high-end GNSS testing, it is shown how to work with the instrument, followed by a quick user interface tour introducing the most important configuration options and simulation monitoring features.

Mar 19, 2018

High-End GNSS simulation with the R&S®SMW200A - Introduction

This video introduces a new series of videos covering the new R&S®SMW200A GNSS simulator. A general discussion of today’s GNSS testing needs is followed by an overview of key features and possible GNSS configurations for the R&S®SMW200A.

Mar 19, 2018

Test solution for NGeCall modules presented at GSMA MWC 2018

Rohde & Schwarz demonstrated a test solution for Next Generation eCall (NGeCall) modules at the GSMA Mobile World Congress 2018 in Barcelona.

Mar 09, 2018

Field-to-lab testing of cellular devices presented at GSMA MWC 2018

Rohde & Schwarz presented tools to reduce expensive and time-consuming drive tests for LTE, NB-IoT and eMTC devices at the GSMA Mobile World Congress 2018 in Barcelona.

Mar 09, 2018

First cellular V2X signaling solution for 3GPP Rel.14 presented at GSMA MWC 2018

Rohde & Schwarz presented a protocol and application test solution for cellular V2X (C-V2X) at the GSMA Mobile World Congress 2018 in Barcelona.

Mar 09, 2018

Demander des informations

Vous avez des questions ou besoin d'informations supplémentaires ? Remplissez simplement ce formulaire et nous vous recontacterons rapidement.

Marketing de permission

Je souhaite recevoir des informations de Rohde & Schwarz via

Qu'est ce que cela signifie en détail ?

Je reconnais que les entités ROHDE & SCHWARZ GmbH & Co. KG et ROHDE & SCHWARZ ou toute autre société subsidiaire mentionnée au sein de ce site Internet, peuvent me contacter par le moyen de leur choix (email ou courrier) pour des raisons marketing et publicitaires (par exemple pour des informations sur des offres spéciales et des promotions) en relation avec, mais pas uniquement, des produits et des solutions dans les domaines du test et mesure, des communications sécurisées, de la surveillance et test des réseaux, des broadcasts et médias, ainsi que de cybersécurité.

Vos droits

Cette déclaration de consentement peut être révoquée à tout moment par l'envoi d'un courriel portant, dans son objet, la mention "Unsubscribe" (désinscription) à news@rohde-schwarz.com. En outre, chaque courriel envoyé contient un lien vers une fonction de désinscription de publicités ultérieures adressées par courrier électronique. La "Déclaration de confidentialité" expose plus en détail l'utilisation des données personnelles, ainsi que la procédure de révocation de consentement.

Votre demande a bien été envoyée ! Nous vous contacterons dans les plus brefs délais.
An error is occurred, please try it again later.