SMW200A Mediacenter

Demystifying 5G – Backpack for simultaneous 5G NR and LTE coverage measurements

The video introduces a compact backpack that is ideal to perform simultaneous network measurements of 5G NR in mmWave and sub 6 GHz frequencies.


Demystifying 5G – Concept of SSB beamforming in mmWave frequencies

The video explains the concept of synchronization signal blocks (SSB), how SSB beamforming works in sub 6 GHz and mmWave frequencies and how many different beams can be realized by the network infrastructure.


Demystifying 5G – Simultaneous coverage measurements on LTE and 5G NR at 28 GHz

The video demonstrates the simultaneous measurement of 5G NR signals in the mmWave frequency range at 28 GHz and LTE in sub 6 GHz using a single network scanner in a 5G backpack for coverage and beamforming tests.


Demystifying 5G – Frequency settings in 5G NR

The video provides insights into the channel raster and synchronization raster in 5G NR in order to explain how to perform coverage measurements for 5G non-standalone and standalone mode.


Demystifying 5G – Automatic channel detection (ACD) measurement for 5G NR

The video demonstrates how the automatic channel detection (ACD) option eases 5G coverage measurements even in the mmWave frequency range.


High-End GNSS simulation with the R&S®SMW200A - Episode 5

The performance of GNSS receivers must be validated and characterized not only under ideal conditions, but also in the presence of other communication signals like GSM, UTMS or LTE.


High-End GNSS simulation with the R&S®SMW200A - Episode 4

Unintentional or intentional interference can significantly impair the reception of GNSS signals.


High-End GNSS simulation with the R&S®SMW200A - Episode 6

This video shows how to perform advanced interferer simulations for testing multi-antenna GNSS receivers with anti-jam capabilities, also known as Controlled Reception Pattern Antennas (CRPAs).


Clock and LO components in 5G base stations (part 3/3)

Monitoring and relocking clock inputs are critical for the performance and the timing of 5G base station transceivers.


Be first for 5G signal generation and analysis presented at GSMA MWC 2017

Rohde & Schwarz demonstrated 5G component characterization at 28 GHz at the GSMA Mobile World Congress 2017 in Barcelona.


Compact and scalable beamforming power measurements presented at GSMA MWC 2017

Rohde & Schwarz presented the first over-the-air power measurement solution for 5G and IEEE 802.11ad/11ay components at the GSMA Mobile World Congress 2017 in Barcelona.


5G channel sounding

Rohde & Schwarz in cooperation with Fraunhofer HHI realize a novel channel sounding solution.


Webinar: Radar signal generation

This webinar discusses the test requirements of next generation single-channel and multichannel digital receivers and demonstrates an efficient and comprehensive test solution based on the R&S®Pulse Sequencer software in combination with the R&S®SMW200A vector signal generator.


Testing LTE-U capable eNodeB with R&S®SMW200A and R&S®FSW

This video explains the LTE-U technology and demonstrates how to efficiently measure LTE signals in the 5 GHz unlicensed band on eNodeBs using the R&S®SMW200A vector signal generator and the R&S®FSW signal and spectrum analyzer from Rohde & Schwarz.


High-End GNSS simulation with the R&S®SMW200A - Episode 3

In this third video of R&S’s new video series on high-end GNSS testing, it is shown how to set up a multi-constellation, multi-frequency GNSS scenario and feed the GNSS signals to a connected GNSS receiver.


High-End GNSS simulation with the R&S®SMW200A - Introduction

This video introduces a new series of videos covering the new R&S®SMW200A GNSS simulator. A general discussion of today’s GNSS testing needs is followed by an overview of key features and possible GNSS configurations for the R&S®SMW200A.


High-End GNSS simulation with the R&S®SMW200A - Episode 2

In this second video of R&S’s new video series on high-end GNSS testing, it is shown how to work with the instrument, followed by a quick user interface tour introducing the most important configuration options and simulation monitoring features.


Unleashing 5G mm-wave frequencies presented at GSMA MWC 2015

Rohde & Schwarz demonstrated a test setup for broadband 5G applications in the millimeter wave range at the GSMA Mobile World Congress 2015 in Barcelona. The setup based on the R&S®SMW200A vector signal generator and the R&S®FSW signal and spectrum analyzer can test bandwidths up to 2 GHz, which is 100 times larger than in current LTE networks.


Higher order MIMO testing - 4x4 channel simulation demonstration

Highly developed standards such as LTE and WLAN 802.11ac presuppose MIMO. MIMO testing requires a signal generator with multipath and standard-compliant fading simulation in all signal paths. The R&S®SMW200A vector signal generator can internally simulate all MIMO constellations up to 8x2, including fading.


Webinar: Advanced multi-emitter radar simulation with off-the-shelf T&M equipment

Test scenarios can range from simple pulses for component tests to full scale testing of complex radar systems. Examples show how to map real signal environments with multiple emitters and interferers into vector signal generators to stimulate a system under test.


R&S®SMW200A - Interferer, AWGN Generation and Realtime Fading Simulation

Demonstration of generating interferer signals, generating AWGN signals, applying realtime fading - all within a single instrument.


R&S®SMW200A - SCPI Recorder and Code Generator

Demonstration of test automation feature for speeding up program code development.


R&S®SMW200A - Generating LTE Signals

Demonstration of how to create LTE and LTE-Advanced signals, for example with cross-carrier scheduling for carrier aggregation.


R&S®SMW200A vector signal generator

The R&S®SMW200A vector signal generator is the ideal tool for generating the high-quality, complex digitally modulated signals required for the development of new wideband communications systems or the verification of 3G and 4G base stations.


Related solutions

5G NR testing

More information

5G OTA/massive MIMO testing

More information

IoT testing

More information

Request information

Do you have questions or need additional information? Simply fill out this form and we will get right back to you.

Marketing permission

I want to receive information from Rohde & Schwarz via

What does this mean in detail?

I agree that Rohde & Schwarz GmbH & Co. KG and the Rohde & Schwarz entity or subsidiary company mentioned in the imprint of this website, may contact me via the chosen channel (email or postal mail) for marketing and advertising purposes (e.g. information on special offers and discount promotions) related to, but not limited to, products and solutions in the fields of test and measurement, secure communications, monitoring and network testing, broadcast and media, and cybersecurity.

Your rights

This declaration of consent may be withdrawn at any time by sending an email with the subject "Unsubscribe" to Additionally, a link to unsubscribe from future email advertisements is contained in each email sent. Further details on the use of personal data and the withdrawal procedure are set out in the Statement of Privacy.

Your request has been sent successfully. We will contact you shortly.
An error is occurred, please try it again later.