Search Application Notes & Cards
Learn how to configure Rohde & Schwarz products to fit your application. Search our database by product, technology, or application to find relevant technical documents.
Search Application Notes & Cards
Learn how to configure Rohde & Schwarz products to fit your application. Search our database by product, technology, or application to find relevant technical documents.
1104 Results
Analyzing RF pulses is a key aspect of pulsed radar applications, e.g. in air traffic control (ATC), maritime radar or scientific measurements of the ionosphere. It is essential to analyze the pulse envelope in the time domain because it contains important information needed to characterize the application. The R&S®RTO digital oscilloscope is a very useful measurement instrument for analyzing pulse characteristics.
09-Nov-2017
This Application Note gives a short overview how signals with two different modulation schemes can be analyzed using the R&S®FSW (or R&S®FPS) using its Multi-Standard-Radio-Analyzer (MSRA) and Vector Signal Analysis personality. The Application Note focuses on DVB-S2(X) signals, but the approach may be used for similar signals as well, as e.g. used in microwave backhaul links.The Application Note also provides a software tool that automates the configuration and provides the variety of different constellations that are used within DVB-S2(X).
18-Apr-2016 | AN-No. 1EF93
High sampling rate and automatic pulse analysis make the R&S®NRP-Z8x wideband power sensors ideal for time-domain analysis of radar pulses.
06-Aug-2013
The R&S®FSMR3000 (hereinafter FSMR) is a three-in-one instrument incorporating a Measurement Receiver, a Signal and Spectrum Analyser, and a Phase Noise Analyser.This application note demonstrates the use of the FSMR, including the Cross-correlation option (R&S®FSMR3-B60), to measure the Phase Noise characteristics of a raw Signal Generator (R&®SMA100B).The Cross-correlation phase noise measurement improves sensitivity by 5 · log(n) dB, compared with measurements that do not use this option. For example, a measurement using 10 correlations, improves the phase noise floor by 5 dB.
31-Dec-2021 | AN-No. 1SL376
This document presents a simple procedure for network analysis that is more cost-effective than the use of scalar network analyzers. It allows the accurate measurement of the transmission characteristics of filters, amplifiers and frequency converters over a large frequency and dynamic range. In order to reach very high measurement speeds, Rohde & Schwarz signal generators are operated in 'List Mode', and Rohde & Schwarz power meters are operated in 'Buffered Mode.' The required programming for the signal generator and the power meter is illustrated by excerpts from a Visual Basic program which is available, free of charge, upon request.
14-Jul-2006 | AN-No. 1MA101
Long acquisitions at maximum resolution with the history function
01-Dec-2017
This application note describes how to set up 3GPP FDD and LTE multicell and multi-UE scenarios with the R&S®SMU200A with a focus on routing and leveling of the baseband signals. Furthermore, it describes in detail how to determine the correct AWGN settings, i.e. how to calculate the required signal-to-noise ratio for the various scenarios.
10-Aug-2011 | AN-No. 1GP80
This application note describes how to remotely control the R&S SGMA RF sources SGT100A and SGS100A with a special focus on their high-speed remote control capabilities via LAN based FAST Socket or FAST PCI Express (PCIe) connections which allow round trip setting times of only 100μs.It therefore provides a brief introduction into the general remote control capabilities, explains the interaction of the different SW protocol layers and drivers, and in detail describes how to establish a high-speed remote control connection. Finally, a comparison of the measured setting time performance of the different remote control approaches is provided.
12-May-2016 | AN-No. 1GP107
This application note shows how to perform LTE terminal block error rate (BLER) and throughput tests under fading conditions with the R&S®CMW500 Protocol Tester and the R&S®AMU200A Fading Simulator.
27-Mar-2012 | AN-No. 1MA177
This application note describes the noise figure measurement using the R&S Vector Network Analyzers of the ZVA and ZVT series. It explains the concept of measuring noise figure without the need for a characterized noise source. Furthermore, it discusses different measurement applications and the respective setup and implications. Some examples guide through the instrument setups and show measurement results as well.
27-Oct-2010 | AN-No. 1EZ61
The R&S®FSW signal and spectrum analyzer with the R&S®FSW-K160R realtime option and the R&S®FSW-K6 pulse measurement option is ideal for testing modern radars.
04-Jul-2013
The 3GPP TS 36.521-1 “Radio transmission and reception” LTE User Equipment (UE) conformance specification defines the measurement procedures for LTE terminals with regard to their transmitting characteristics, receiving characteristics and performance requirements as part of the 3G Long Term Evolution (3G LTE) standard. This application note describes how to use the LTE Frequency Division Duplex (FDD) and Time Division Duplex (TDD) measurement functionality provided by the R&S®CMW500 wideband radio communication tester to perform LTE transmitter and receiver measurements according to this test specification.
17-May-2013 | AN-No. 1CM94
Near Field Communication (NFC) is a new short-range, standards-based wireless connectivity technology, that uses magnetic field induction to enable communication between electronic devices in close proximity. Based on RFID technology, NFC provides a medium for the identification protocols that validate secure data transfer. NFC enables users to perform intuitive, safe, contactless transactions, access digital content and connect electronic devices simply by touching or bringing devices into close proximity. This White Paper gives an overview of NFC uses, NFC technology and signals and RF measurements on NFC units. NFC analog measurements with R&S test instruments are described in detail in R&S application Note 1MA190 'Basic Tests of NFC Enabled Devices Using R&S Test Equipment'
03-Jun-2013 | AN-No. 1MA182
3GPP TS36.141 defines conformance tests for EUTRA base stations (eNodeB). Release 14 added several tests, especially for enhanced License Assisted Accsess (eLAA).This application note describes how all required transmitter (Tx) tests (TS36.141 Chapter 6) can be performed quickly and easily by using signal and spectrum analyzers from Rohde & Schwarz. A few tests additionally require signal generators from Rohde & Schwarz.Examples illustrate the manual operation. A free software program enables and demonstrates remote operation.The LTE base station receiver (Rx) tests (TS36.141 Chapter 7) are described in Application Note 1MA195.The LTE base station performance (Px) tests (TS36.141 Chapter 8) are described in Application Note 1MA162.
11-May-2016 | AN-No. 1MA154
Combining the R&S®UPP audio analyzers with the R&S®SMB100A signal generators provides the most compact and fastest test solution for modern FM car radios
19-Feb-2015
The antenna patterns of automotive radars provide a wealth of information that is of vital importance during radar development and validation.
28-Oct-2020
The test case wizard enables the signal generator to set up all required parameters for conformance testing of 5G NR base stations in no time with just a few clicks.
25-May-2021
This application note explains the fundamentals of the cell search and cell selection and reselection procedures required for both modes of UMTS Long Term Evolution: FDD and TDD. It describes how to generate and analyze the required signals using Rohde & Schwarz test and measurement solutions. The application note also shows how to perform interoperability tests and terminal conformance tests according to the baseline of the 3GPP specifications for protocol conformance and Radio Resource Management (RRM).
17-Sep-2009 | AN-No. 1MA150
This application note helps the user to configure a Rohde & Schwarz vector signal generator for LTE FDD repeater conformance testing. It explains step by step how to set up the baseband signal for the various test cases defined in the 3GPP Technical Specification 36.143.The R&S®SMx vector signal generators provide predefined, LTE-conform test models and are therefore ideal for LTE repeater conformance testing. The test cases in TS 36.143 can be set up with a single instrument which provides all necessary test signals including the four specified repeater stimulus signals.
26-Apr-2013 | AN-No. 1GP85
The scope of this application note is to give a comprehensive guide on how the R&S®FSW signal and spectrum analyzer with the option R&S®FSW-K18 may be used to create a Hammerstein model for the R&S®SMW200A vector signal generator’s output stage. This model can then be applied to counteract inherent non-linearities and memory effects and improve the Error Vector Magnitude (EVM) at high output powers of the R&S®SMW200A vector signal generator.
28-Aug-2023 | AN-No. 1GP139
The signal purity of clock sources has a direct impact on system performance. To ensure proper operation, it is necessary to verify that the purity meets the design requirements.
30-Sep-2021
The R&S®CMW500 and R&S®SMBV100B are the ideal team for motor vehicle type approval testing of your eCall and ERA-GLONASS cellular modems and their GNSS receivers in line with the EU2017/79 regulation.
02-May-2022
The measurement speed for spurious signal measurements is mainly defined by the spectrum analyzer sweep speed. With traditional swept spectrum analyzers and tight spurious limits the measurement can easily take hours or even a full day. This application note describes the differences in sweep speed between swept spectrum analyzers and modern spectrum analyzers with a wide-band FFT process, and how this improves the measurement speed for general spurious measurement.
10-Jul-2012 | AN-No. 1EF80
Bluetooth Low Energy (BLE) 5.1 has introduced Angle of Arrival (AoA) and Angle of Departure (AoD) to enrich the direction finding (DF) feature. This application note gives the guidance of how to perform the BLE 5.1 DF RF tests according to the RF test specification of BT 5.1 by using the Rohde & Schwarz test solutions.
30-Oct-2019 | AN-No. GFM327
This application note explains how to detect, characterize, find and document interferers in cellular networks using the R&S®FSH spectrum analyzer.First it explains how to use the spectrum and interference analysis functions during each step of interference hunting. It also illustrates the explanations with a common interferer example. Then it points out the most common interference sources in cellular networks and gives tips on how to identify them.
21-Oct-2014 | AN-No. 1EF89
The development and proliferation of Bluetooth® is a unique success story. The number of Bluetooth® wireless technology enabled devices is currently growing by 3.6 billion per year. As Internet of Things (IoT) technology advances, this number will grow significantly over the next years. Bluetooth SIG anticipates that there will be nearly 5.6 billion new Bluetooth® enabled devices in 2022. To ensure connectivity and trouble-free operation, each Bluetooth® enabled device has to be tested for conformance with Bluetooth SIG standards and regulatory requirements.
23-Nov-2017
In high-speed digital measurement applications, test fixtures are commonly used to connect devices under test to measurement equipment. Characterization, and analysis in the time and frequency domains that accounts for various constraints helps to remove the influence of these fixtures.
23-May-2023 | AN-No. 1SL393
The R&S®CMW Wideband Radio Communication Tester offers an elaborate parametric test concept, including all RF test cases up to Bluetooth®5, that makes this flexible test platform ideal for designing and verifying Bluetooth® Low Energy (LE) circuitsand modules.
27-Jan-2017
LTE is under continuous development. Release 10 (LTE-Advanced) introduced carrier aggregation (CA) as the primary enhancement. Releases 11 and 12 add several new components to LTE. Some are enhancements to existing features (such as improvements to CA), while others are completely new concepts, such as coordinated multipoint (CoMP).This application note summarizes the Rohde & Schwarz test solutions for LTE-Advanced according to Releases 11 and 12 using vector signal generators, signal and spectrum analyzers and the wideband radio communication tester.
14-Jul-2016 | AN-No. 1MA272
Power amplifiers in digital TDMA mobile phones are fed with current only during the active slot to save power. Using conventional measuring equipment, the noise figure, an important parameter in power amplifiers, can only be determined with the amplifier in continuous operation. However, continuous operation can lead to amplifier overload and produce distorted results. Now there is a convenient way of determining the noise figure of amplifiers with pulsed power supply: using a Spectrum Analyzer (FSP or FSE or FSIQ or ESI), Noise Measurement Software FS-K3 and a function or pulse generator.
19-Dec-2000 | AN-No. 1MA32