26 결과
로데슈바르즈 기기용 다목적 소프트웨어 툴RSCommander는 로데슈바르즈의 스펙트럼 분석기, 네트워크 분석기, 신호 발생기, 오실로스코프에서 사용하는 다목적 소프트웨어 툴입니다. 이 소프트웨어는 기기를 자동으로 검색하고 스크린샷 캡처나 트레이스 읽기, 파일 전송과 같은 작업과 간단한 스크립트를 생성시 사용할 수 있습니다.
12월 24, 2017 | AN-번호 1MA074
이 애플리케이션 노트는 MathWorks MATLAB에서 로데슈바르즈 기기를 원격 제어하는 두 가지 방식에 대해 살펴봅니다.첫 번째는 VISA 연결과 다이렉트 SCPI 명령을 사용하는 방법입니다.두 번째 방식은 로데슈바르즈 VXI Plug&Play 기기 드라이버와 MATLAB Instrument Control 툴박스를 이용합니다.
6월 12, 2017 | AN-번호 1MA171
3GPP TS36.141은 EUTRA 기지국(eNodeB)의 적합성 테스트를 정의합니다. Release 14에는 특히 eLAA(enhanced License Assisted Accsess)에 대한 몇 가지 테스트가 추가되었습니다.이 애플리케이션 노트는 로데슈바르즈의 신호 및 스펙트럼 분석기를 사용하여 필요한 송신(Tx) 테스트(TS36.141 Chapter 6)를 쉽고 빠르게 수행하는 방법에 대해 설명합니다. 일부 테스트는 로데슈바르즈의 신호 발생기를 추가해야 합니다.예제는 수동 운용 기준입니다.무료 소프트웨어 프로그램으로 원격 조작이 가능하며, 데모를 볼 수 있습니다.LTE 기지국 수신(Rx) 테스트(TS36.141 Chapter 7)에 대한 설명은 애플리케이션 노트 1MA195에 나와 있습니다.LTE 기지국 송신(Px) 테스트(TS36.141 Chapter 8)에 대한 설명은 애플리케이션 노트 1MA162에 나와 있습니다.
5월 11, 2016 | AN-번호 1MA154
R&S®SMW200A Signal Generator의 Baseband 페이딩은 이동통신 무선 표준 테스트에서 정상적으로 검증되었으며 폭넓게 승인되고 있습니다. 어떤 어플리케이션에서는 RF 신호를 반드시 페이딩해야만 하는 경우가 있습니다. 다목적 RF Fading Simulator는 R&S®FSW, R&S®FSQ, R&S®FSG, R&S®FSV Signal Analyzer(Digital Base Band Interface 탑재) 또는 R&S®TSMW / R&S®IQR 및 R&S®SMU Signal Generator(디지털 Baseband 입력 및 페이딩 시뮬레이터 옵션 탑재) 기기 조합으로 쉽게 구축할 수 있습니다. 이에 대한 구체적인 방법을 설명합니다.
2월 27, 2015 | AN-번호 1MA145
MIMO(Multiple Input Multiple Output)는 LTE의 핵심 부분입니다. 로데슈바르즈의 벡터 신호 발생기와 신호 및 스펙트럼 분석기는 최대 4채널의 LTE 측정을 지원합니다. 이 애플리케이션 노트는 LTE 다운링크의 2x2 MIMO에 대해 살펴봅니다. 무료 프로그램으로 원격 제어 프로그래밍 예제가 제시되어 있습니다.
10월 09, 2014 | AN-번호 1MA143
LTE-Advanced는 3GPP Release 8에 최초로 지정된 기본 LTE 기술을 개선하는 복수의 기능으로 구성되어 있습니다. LTEAdvanced와 같은 개선이 포함된 LTE는 ITU에서 IMT-Advanced 요구사항을 준수하는 것으로 승인함에 따라 4G 이동통신 시스템으로 적합합니다. LTE-Advanced의 다른 기술 요소는 시장 우선 순위가 다르며 다른 테스트 전략이 필요합니다. 이 애플리케이션 노트에서는 벡터 신호 발생기, 신호 및 스펙트럼 분석기, Wideband Radio Communication Tester를 이용하는 LTE-Advanced(Release 10)용 로데슈바르즈 테스트 솔루션에 대해 간략히 설명합니다.
9월 03, 2014 | AN-번호 1MA166
IQWizard는 FSx Spectrum Analyzer 또는 ESx Receiver를 사용하여 다양한 형식의 IQ 신호 포맷을 로드하고 IQ 신호를 측정하는 툴입니다. 메모리에서 획득한 IQ 데이터는 다양한 형식으로 저장하거나 WinIQSIM™ 또는 WinIQSIM2™를 사용하여 R&S® 벡터 신호 발생기로 전송할 수 있습니다.
4월 26, 2013 | AN-번호 1MA028
가장 빠르게 성장하는 모바일 무선 표준인 LTE는 3GPP Release 8에서 시작되었습니다. 초기 개선 사항과 새 기능은 Release 9에 구현되어 있습니다. 이 애플리케이션 노트는 로데슈바르즈 기기를 사용하여 LTE Release 9 기능의 측정 방법에 대해 설명합니다.
4월 26, 2013 | AN-번호 1MA210
Multiple input multiple output (MIMO) technology is an integral part of 3GPP E-UTRA long term evolution (LTE). As part of MIMO, beamforming is also used in LTE. This application note provides a brief summary of the transmission modes (TM) in LTE and describes the beamforming measurements for base stations (BS) and user equipment (UE). The T&M options using various Rohde & Schwarz instruments are also presented.
Apr 26, 2013 | AN-번호 1MA187
The aim of this application note is to provide information regarding Rohde & Schwarz instrument drivers. This paper shall help application engineers and software developers to easily get an understanding of advanced techniques to develop test and measurement (T&M) applications by utilizing Rohde & Schwarz instrument drivers. Furthermore the nomenclature used for Rohde & Schwarz instrument drivers will be explained.
Jan 01, 2013 | AN-번호 1MA153
The use of Rohde & Schwarz device drivers under VEE software is not complicated. However, a number of factors are involved, the errors that occur are often difficult to diagnose. This application provides easy and detailed support for installation and troubleshooting using National Instruments or Agilent GPIB boards.
Dec 20, 2012 | AN-번호 1MA035
This white paper introduces a novel attribute based architecture for VXIplug&play instrument drivers. The presented architecture uses the attribute based concept of IVI-C instrument drivers to introduce a two-layer design for VXIplug&play instrument drivers. Moreover the use of attributes is shown for the Rohde & Schwarz Spectrum Analyzer (rsspecan) instrument driver.
Dec 01, 2012 | AN-번호 1MA170
This white paper provides a brief technology introduction on the 802.11ac amendment to the successful 802.11-2007 standard. 802.11ac provides mechanisms to increase throughput and user experience of existing WLAN and will build on 802.11n-2009.
May 23, 2012 | AN-번호 1MA192
This application note provides a guide through the measurements for IEEE 802.11ac WLAN transmitter signals using the general purpose OFDM analysis software R&S FS-K96. Step-by-step instructions for performing the measurements are provided and the different result types available with the FSK96 Software are discussed.
Sep 22, 2011 | AN-번호 1EF82
기존 GSM 이동 통신 시스템은 3rd Generation Partnership Project(3GPP) GSM/EDGE Radio Access Network(GERAN) Release 9 규격에 지정된 "Voice Services over Adaptive Multi-user Channels on One Slot" (VAMOS) 기능을 추가하여 음성 용량을 두 배로 늘릴 수 있습니다. 이 애플리케이션 노트는 에어 인터페이스의 관점에서 VAMOS 기능에 대해 자세히 설명하며, 로데슈바르즈 테스트 장비에서 제공하는 VAMOS 테스트 솔루션에 대해 구체적으로 살펴봅니다.
8월 17, 2011 | AN-번호 1MA181
Verification of baseband data is an important step in the early development phase of LTE/LTE-A-ready products. Comparison values for baseband data (test vectors) from other sources can be very useful in order to verify the correct implementation of the standard. Option K81 for the R&S®SMx200A vector signal generator offers sample data for LTE at the bit level. The reference data enables users to test their own implementation of the specification. The LTE bit stream verification program shown here uses data generated by this option and offers a (bitwise) comparison with bit streams generated for an LTE downlink signal. Therefore it demonstrates, how easy the option R&S SMx-K81 can be integrated into the simulation and design process during the development of LTE/LTE-A handsets or base stations.
Feb 02, 2011 | AN-번호 1MA161
이 애플리케이션 노트는 로데슈바르즈 스펙트럼 분석기, 로데슈바르즈 신호 발생기 및 R&S FS-Z10 Coherence Unit을 사용하여 두 RF 신호 간 정합성(위상, 타이밍, 게인 차이)을 측정하는 방법에 대해 설명합니다.
9월 28, 2010 | AN-번호 1EF70
이 애플리케이션 노트는 R&S® 테스트 및 계측 제품을 GPIB 또는 LAN 인터페이스를 통해 AWR® Visual System Simulator™(VSS)에 빠르고 원활하게 연결하는 방법에 대해 설명합니다. 로데슈바르즈 하드웨어에 맞춰진 AWR® Connected™와 R&S® WinIQSIM2™ Signal Simulation 소프트웨어를 사용하여 디지털 무선 표준들의 유연성에 대해 자세히 알아보고 VSS에 통합하는 방법을 설명합니다.
5월 20, 2010 | AN-번호 1MA174
This application note explains how to create screenshots of Rohde & Schwarz instruments using instrument drivers. The presented examples are written in C (LabWindows/CVI), C# programming language and LabVIEW. The examples are available at the instrument driver download site.
Dec 11, 2009 | AN-번호 1MA160
This application note explains the fundamentals of the cell search and cell selection and reselection procedures required for both modes of UMTS Long Term Evolution: FDD and TDD. It describes how to generate and analyze the required signals using Rohde & Schwarz test and measurement solutions. The application note also shows how to perform interoperability tests and terminal conformance tests according to the baseline of the 3GPP specifications for protocol conformance and Radio Resource Management (RRM).
Sep 17, 2009 | AN-번호 1MA150
Modern radio communication systems have to provide higher and higher data rates. As conventional methods like using more bandwidth or higher order modulation types are limited, new methods of using the transmission channel have to be used. Multiple antenna systems (Multiple Input, Multiple Output – MIMO) gives a significant enhancement to data rate and channel capacity. This application note gives an introduction to basic MIMO concepts and terminology and explains how MIMO is implemented in different radio communications standards.
Jul 02, 2009 | AN-번호 1MA142
이 애플리케이션 노트는 OFDM 측정 소프트웨어인 R&S FSQ-K96의 사용에 대해 설명합니다. 특히 소프트웨어의 사용 사례, 셋업, 기능, 설정, 결과에 대해 살펴봅니다. 또한, R&S FSQ-K96의 구성 파일, R&S FSQ 신호 분석기에 적절한 IQ 데이터 파일, R&S 신호 발생기용 파형 파일 생성에 대해 자세히 다룹니다. 이를 바탕으로 일반적인 OFDM 신호의 신호 발생 및 분석을 위한 완벽한 R&S 테스트 솔루션을 구축하는 방법을 확인할 수 있습니다.
10월 17, 2008 | AN-번호 1EF65
PICC(Proximity-Integrated-Circuit-Cards)에서 방사되는 EMD(Electromagnetic Disturbance)는 부하 변조의 원치 않는 형태입니다. 이 애플리케이션 노트는 벡터 신호 분석을 사용하여 데이터 전송 중 EMD를 측정하는 방법에 대해 설명합니다.
10월 19, 2007 | AN-번호 1MA120