Non-cellular device manufacturing

Mass production of non-cellular devices that support technologies such as WLAN 802.11a/b/g/n/p/ac/ax, Bluetooth® classic (BT/EDR) and low energy (LE), ZigBee and LR-WPAN requires optimized test setups in production lines in order to detect manufacturing defects and ensure the expected quality of a wireless device. This can be achieved by testing the devices in non-signaling mode, where the sequencer software communicates with the chipset directly over different physical interfaces offered by the non-cellular device.

Test setup for testing devices with different physical interfaces

R&S®CMWrun supports testing of such devices with different physical interfaces such as USB, PCIe, Serial, ADB, SDIO and Telnet. R&S®CMWrun combined with the R&S®CMW100 multiport communications manufacturing test set is a compact and cost effective turnkey test solution for quickly verifying TX and RX characteristics on the production line.

Products for non-cellular device testing

  • R&S®CMW100 Communications Manufacturing Test Set
    • Versatile: supports all non-cellular technologies such as IEEE 802.11a/b/g/n/p/ac, BT classic (BT/EDR) and low energy (LE), ZigBee, LR-WPAN and GPS in the sub 6 GHz band
    • High throughput and efficient: eight bidirectional ports enable multi-DUT testing for high overall throughput
    • Highly accurate: fully automatic level correction for highly accurate measurements
    • Eco-friendly: small footprint for minimal space requirements, low energy consumption
  • R&S®CMWrun Sequencer Software Tool
    • Production-ready sequencer tool for parallel multi-DUT testing with integrated chipset control
    • Supports communications to device under test with different types of physical interfaces
    • Measurement reports with pass/fail status indications
    • Test results storable in the custom database

Power Supply

  • The right power supply for the right application
  • Low ripple and stable voltages

High performance and accurate higher order MIMO testing

Non-cellular devices such as access points, routers, CPE and TV set-top boxes supporting IEEE 802.11n/ac often apply multiple antenna schemes like 2x2 MIMO, 3x3 MIMO or even higher order MIMO. This offers additional challenges in a production line where the goal is to use as few test and measurement resources as possible to measure signal characteristics on all multiple antenna streams.

Switched MIMO test setup for IEEE 802.11ac 4x4 MIMO access point with R&S®CMW100

The R&S®CMW100 multiport tester is ideal for MIMO testing. Each DUT antenna port is connected to an individual RF port on the tester. In “switched MIMO” mode, each antenna port is measured separately providing, for example, the modulation quality for each stream. The test setup can also be easily scaled up to test multiple DUTs.

Multi-DUT testing for MIMO and TX beamforming using R&S®CMW100 and R&S®CMWrun

In addition to switched MIMO, the R&S®CMW100 supports other MIMO variants such as composite MIMO, TX beamforming calibration and verification (required for devices that support implicit beamforming). This solution offers the best accuracy for higher order MIMO measurements.

Products for higher order MIMO testing

  • R&S®CMW100 Communications Manufacturing Test Set
    • Future-proof: multitechnology solution with a frequency range up to 6 GHz
    • High throughput and efficient: eight bidirectional ports enable multi-DUT testing for high overall throughput
    • Highly accurate: fully automatic level correction for highly accurate measurements
    • Eco-friendly: small footprint for minimal space requirements, low energy consumption
  • R&S®CMWrun Sequencer Software Tool
    • Includes chipset-specific libraries with ready-to-go test plans for complex measurements
    • Supports most chipsets available in the industry
    • Measurement reports with pass/fail status indications
    • Test results storable in the custom database

Cost-effective go/no-go test solution for final testing

Go/no-go test solution using the R&S®NRP power sensor and R&S®OSP switching unit

After final assembly, it is necessary to test the proper functioning of the non-cellular device. This calls for a cost-effective solution to perform simple RF power measurements to verify the DUT’s transmitter.

The R&S®NRP power sensors are ideal for measuring the output power transmitted from any non-cellular device such as an access point or router.

The R&S®OSP open switch and control platform is a speed-optimized solution that ensures fastest switching between different antenna ports, enabling simultaneous testing of multiple DUTs. Combining realtime power measurements with the fast switching capabilities of the R&S®OSP yields a cost-effective and simple test setup for verifying the proper functioning of non-cellular devices.

Products for go/no-go testing

  • R&S®OSP Open Switch and Control Platform
    • Plug and play RF switch and control platform
    • Easy, reliable and independent switching of different switching paths with just one command
    • Easy integration into an ATE system with Ethernet interface

Power Meter & Voltmeter

  • Cost-effective and compact: operation on a laptop/PC via USB
  • Comprehensive portfolio, from DC to 110 GHz, from –67 dBm to +45 dBm
  • Up to 90 dB dynamic range with three-path diode power sensors
  • Top accuracy with thermal power sensors
  • Up to four R&S®NRP-Zxx power sensors can be simultaneously connected to the R&S®NRP2 base unit

5G T&M 솔루션

감사합니다.

요청이 성공적으로 전송되었습니다!

곧 연락 드리겠습니다.

로데슈바르즈 팀 드림

문의 양식

문의 사항을 입력하십시오.

귀하의 호칭을 선택해 주십시오.
연락처 정보

이름을 입력하십시오.

정확한 이메일 주소를 입력해 주십시오.

회사 이름을 입력하십시오.

우편번호를 입력하십시오.

이름을 입력하십시오.

전화번호를 입력하십시오.

국가를 입력하십시오.

시 이름을 입력하십시오.

주소를 입력하십시오.

번호를 입력하십시오.

(예: 2층, 뒤쪽 건물)

이메일, 우편 또는 전화로 더 이상 해당 정보를 받고 싶지 않을 경우 campaigns@rohde-schwarz.com 으로 귀하의 이메일 주소와 전화 번호를 기재한 메시지를 보내어 본인의 개인 데이터를 홍보 목적으로 사용하는 것을 중단할 수 있습니다.

모든 개인 정보는 로데슈바르즈개인정보 보호정책에 따라 처리됩니다.

보안 응답 코드
show captcha

입력 내용이 올바르지 않습니다.
Do not enter data in this field
*필수 항목
감사합니다.

요청이 성공적으로 전송되었습니다!

곧 연락 드리겠습니다.

로데슈바르즈 팀 드림

정보 요청
주제: No Solution assigned to this page!

문의 사항을 입력하십시오.
연락처 정보

귀하의 호칭을 선택해 주십시오.

이름을 입력하십시오.

정확한 이메일 주소를 입력해 주십시오.

회사 이름을 입력하십시오.

우편번호를 입력하십시오.

이름을 입력하십시오.

전화번호를 입력하십시오.

국가를 입력하십시오.

시 이름을 입력하십시오.

주소를 입력하십시오.

번호를 입력하십시오.

(예: 2층, 뒤쪽 건물)
추가 정보


보안 응답 코드
show captcha

입력 내용이 올바르지 않습니다.
*필수 항목
감사합니다.

요청이 성공적으로 전송되었습니다!

곧 연락 드리겠습니다.

로데슈바르즈 팀 드림

피드백
의견을 남겨주세요
주제를 알려 주십시오.

문의 사항을 입력하십시오.
연락처 정보

이름을 입력하십시오.

정확한 이메일 주소를 입력해 주십시오.

이름을 입력하십시오.
보안 응답 코드
show captcha

입력 내용이 올바르지 않습니다.
Do not enter data in this field
*필수 항목
International Website