Learn how to configure Rohde & Schwarz products to fit your application.
35 Results
R&S®VISA is a standardized software library that allows fast communications over diverse interfaces with a wide variety of T&M instruments that are detected on the network from PC applications.
English - 26.05.2020
Fault identification in single elements of antenna arrays is possible by scanning in near-field range and applying the near-field to far-field transformation method.
English - 24.03.2020
R&S®Forum for Instrument Remote Control
English - 28.06.2018
Inside the lab and on the production line – this Rohde & Schwarz solution offers speed, accuracy and convenience for testing TX beamforming passive array antennas.
English - 04.05.2018
English - 29.09.2017
This application note outlines two different approaches for remote-controlling Rohde & Schwarz instruments out of MathWorks MATLAB.
English - 12.06.2017
This document describes the unique application of Rohde & Schwarz VNA to fully characterize the passive part of multi-element antennas.
English - 20.03.2017
This application note focuses on satellite post-launch or on-orbit measurement and monitoring strategies used for satellite functionality checks.
English - 25.11.2016
This white paper provides an overview of test solutions addressing current and future requirements for antenna verification.
English - 11.11.2016
This application note aims to explain test procedures and characterization of the relevant parameters for active phased array antennas.
English - 04.07.2016
This application note describes methods using an R&S®ZVA network analyzer to accurately measure all the key parameters of frequency converters.
English - 30.04.2015
Hints and Tricks for Remote Control of Spectrum and Network Analyzers
English - 19.08.2014
R&S®ZVA, R&S®ZVT Application Sheets
English - 28.07.2014
Welcome to this introductory video show about the R&S ZVA family of network analyzers.
English - 13.02.2014
Direct remote control of OSP via VNA and SA
English - 06.12.2013
Use the R&S®ZVA vector network analyzer and R&S®BBA150 broadband amplifier for accurate and reproducible results in minimum test time.
English - 27.09.2013
This application notes introduces two alternative methods how to do the Power Added Efficiency measurement.
English - 22.05.2013
The R&S®ZVA and the R&S®ZVA-K9 option enables absolute group delay measurements on devices with embedded LO.
English - 17.05.2013
Testing S-Parameters on Pulsed Radar Power Amplifier Modules
English - 11.04.2013
This document describes how a Windows®-based R&S® T&M instrument is remotely operated by an Apple iPad as if working on it locally.
English - 28.03.2013
Development Hints and Best Practices for Using Instrument Drivers
English - 01.01.2013
Rohde & Schwarz Drivers under VEE - Installation and Troubleshooting
English - 20.12.2012
Noise Figure Measurement without a Noise Source on a Vector Network Analyzer
English - 27.10.2010
How to create a Hardcopy using R&S®Instrument Drivers
English - 11.12.2009
GPIBShot - Taking Screenshots via IEEE Bus
English - 28.08.2009
S-Parameters of a 50 to 75 Ohm impedance matching device using R&S ZVx VNA
English - 06.05.2009
Testing Millimeter-Wave Mixers Using Converters of the R&S®ZVA Family
English - 17.11.2008
Tackling the Challenges of Pulsed Signal Measurements
English - 18.01.2008
Millimeter-Wave Measurements Using Converters of the R&S® ZVA Family
English - 09.10.2007
Multiport Millimeter-Wave Measurements Using Converters of the R&S® ZVA Family