R&S®CompactTSVP |
|
1 slot required |
Interfaces
|
Control bus |
|
CompactPCI/PXI |
DUT connector (front) |
|
2 × Mini D Ribbon (MDR) connectors 2 × SMB plug connectors |
Rear I/O connector |
|
CompactPCI connector, 110 pins |
Side connector |
RS-485 |
Semtec terminal strips (2.54 mm) |
Module features
|
Front connectors
|
DIGITAL A/B |
2 × Mini D Ribbon (MDR) connectors |
2 × 8 LVDM data I/O channels 2 × 1 LVDM general purpose I/O channels 2 × 1 LVDM clock I/O channel 2 × 2 LVTTL digital I/O channels |
CLK, TRIG |
2 × SMB connectors |
1 clock I/O channel, 1 trigger I/O channel |
LVDS channels (data input mode)
|
DIGITAL A/B |
|
2 × MDR connectors |
Input modes |
half-duplex operation |
LVDM with termination 100 Ω |
Difference input voltage |
|
max. ±600 mV |
Difference input threshold |
|
min. ±100 mV |
Input resistance |
|
100 Ω |
Realtime acquisition |
sample rate (SDR) |
0.01 bit/s to 100 Mbit/s (10 ns resolution) |
|
sample rate (DDR) |
200 Mbit/s (only for data channels) |
LVDS channels (data output mode)
|
DIGITAL A/B |
|
2 × MDR connectors |
Output modes |
half-duplex operation |
LVDM with termination 100 Ω |
Output voltage |
|VOD|, into 50 Ω load (double termination) |
247 mV (min.), 454 mV (max.) |
Output current |
IOS |
max. 10 mA |
Tristate control |
|
programmable per channel and up to 50 Mbit/s per sample |
Realtime stimulation |
sample rate (SDR) |
0.01 bit/s to 100 Mbit/s (10 ns resolution) |
|
sample rate (DDR) |
200 Mbit/s (only for data channels) |
TTL channels (input/output mode)
|
DIGITAL A/B |
|
2 × MDR connectors |
Input/output mode |
voltage |
3.3 V logic; 10 kΩ pullup onboard |
Realtime stimulation/acquisition |
sample rate |
0.01 bit/s to 50 Mbit/s (10 ns resolution) |
Connector |
onboard connector |
pin connector (terminal strips 2.54 mm) |
Input/output mode |
|
RS-485/422 signal level, 10 bidirectional channels, no RS-485 serial protocol |
Realtime stimulation/acquisition |
sample rate |
0.01 bit/s to 20 Mbit/s with 10 ns resolution |
Realtime stimulation/acquisition memory |
data buffer depth/width (programmable) |
2 M pattern at 32 bits (18 × LVDS, 4 × TTL, 10 × RS-485) |
External clock
|
DIGITAL A/B |
input/output voltage |
according to LVDS channels, 2 × MDR connectors |
|
frequency range |
20 MHz to 50 MHz |
CLK |
input/output voltage |
3.3 V TTL logic (SMB plug) |
|
frequency range |
20 MHz to 50 MHz |
Trigger
|
TRIG |
input/output voltage |
3.3 V TTL logic (SMB plug) |
PXI |
input/output voltage |
8 x PXI, 5 V TTL logic |
Synchronization
|
Trigger units |
applications |
2 x fully independent hardware trigger logic ❙ programmable trigger generator ❙ generation of realtime stimulation clock ❙ generation of realtime acquisition clock ❙ frequency measurement |
Trigger unit characteristics |
reference pattern |
10-bit, 3 states: high, low, don’t care |
|
slope |
positive/negative |
|
trigger delay setting |
0 s to 100 s (10 ns resolution) |
|
output signals |
❙ trigger received signal (pulse) ❙ trigger active signal (start of trigger until burst end) ❙ sample pulse (pulse for each sample) |
Synchronization inputs |
channels |
1 × TTL trigger (TRIG) 8 × PXI trigger bus 1 × pattern comparator |
Synchronization outputs |
channels |
1 × TTL trigger (TRIG) 8 × PXI trigger bus |
|
signals |
❙ output, trigger unit 1 (IT1) ❙ output, trigger unit 2 (IT2) ❙ TTL signal (TRIG) |
General data
|
Environmental conditions
|
Power consumption |
|
5 V: typ. 1 A, 3.3 V: typ. 1 A |
Temperature |
operating temperature range |
+5 °C to +40 °C |
|
storage temperature range |
–10 °C to +60 °C |
Damp heat |
|
+40 °C, 80 % rel. humidity, steady state, in line with EN 60068-2-30 |
Mechanical resistance
|
Vibration |
sinusoidal |
5 Hz to 55 Hz, 0.15 mm amplitude const., 55 Hz to 150 Hz, 0.5 g const., in line with EN 60068-2-6 |
|
random |
10 Hz to 300 Hz, acceleration 1.2 g (RMS), in line with EN 60068-2-64 |
Shock |
|
40 g shock spectrum, in line with MIL-STD-810E, method 516.4, procedure I |
Product conformity
|
Electromagnetic compatibility |
EU: in line with EMC Directive 2014/30/EC |
applied harmonized standards: EN 61326-1: 2013 (industrial environment), EN 61326-2-1: 2013, EN 55011: 2009 + A1: 2010 Group 1, Class A |
Electrical safety |
EU: in line with Low Voltage Directive 2014/35/EC |
applied harmonized standard: EN 610110-1: 2010 |
Dimensions |
W × H × D |
316 mm × 174 mm × 20 mm (12.4 in × 6.8 in × 0.8 in) |
Weight |
|
0.21 kg (0.47 lb) |