The R&S®BBA300 is a robust, compact, ultra-wide band amplifier for use in critical test environments such as EMC, product validation and OTA coexistence in the frequency range of 380 MHz to 18 GHz and RF output power up to 300 W P1dB.

The R&S®SAM100 system amplifier - an ultra-broadband solid state microwave amplifier with outstanding linearity and very good noise characteristics in frequency range from 2 GHz to 20 GHz.

All Rohde & Schwarz oscilloscopes support triggering and decoding of the I²S audio standard, left and right justified and TDM signals. Learn more here.

The R&S®RTO oscilloscope supports triggering and decoding of MIPI D-PHY based protocols DSI and CSI-2. Learn more about the MIPI D-PHY oscilloscope software.

Many R&S oscilloscopes support triggering and decoding of MIL-STD-1553 buses. Explore the supported scopes and learn about MIL-1553 software here.

The R&S®RTO oscilloscope supports triggering and decoding of MIPI M-PHY physical layer and UniPro protocol layer. Learn more about the MIPI M-PHY software.

R&S®RTO2000,; R&S®RTO6 and R&S®RTP oscilloscopes support triggering and decoding of PCI Express Gen 1.1 and 2.0 signals. Explore the PCIe 1.1/2.0 triggering and decoding software.

The R&S®RTP and RTO oscilloscopes supports triggering and decoding of USB 3.1 Gen 1 and Gen 2 signals. Explore the USB 3.1 triggering & decoding software here.

The R&S®RTO and R&S®RTE oscilloscopes support triggering and decoding of USB power delivery signals. Explore the triggering & decoding software here.

The R&S®RTO-K25 option offers an automated test solution for 2.5G/5GBASE-T Ethernet interfaces according to the IEEE test specification. Learn more.

The R&S®MIPI D-PHY compliance test options offer automated test solutions in line with MIPI and UNH-IOL test specifications. Learn more here.

The jitter analysis option extends the functionality of the standard R&S®RTO firmware with a suite of measurement, analysis and visualization tools. More info.

The R&S®RTP-K140/141 options enable the high-speed serial pattern trigger function with a maximum nominal data rate of 8 Gbps or 16 Gbps. More info.

The R&S spectrum analysis oscilloscope software enhances the multichannel spectrum analysis capabilities of R&S oscilloscopes. Explore now!

The TDR/TDT software option creates a time domain reflection (TDR) and time domain transmission (TDT) analysis system for R&S®RTO or RTP oscilloscopes. Explore now!

The IQ software interface significantly simplifies analysis of modulated signals. This option converts modulated signals to I/Q data in realtime. Explore now!

The arbitrary waveform generator option R&S®B6 enhance R&S oscilloscopes with a fully integrated arbitrary waveform and pattern generator. More information.

The R&S®RTA4000 oscilloscope is designed for top-class signal integrity and responsive ultra-deep memory. See more of your signals with the power of 10.

The R&S®RTM3000 oscilloscope offers a 10.1" capacitive display, 10-bit ADC and up to 400 Msample memory depth. Available in bandwidths from 100 MHz to 1 GHz.

R&S®RTO6 is the oscilloscope you can trust. With bandwidths up to 6 GHz, it lets you test & debug your designs quickly. Leverage your expertise now!

R&S®RTP high performance series oscilloscopes benefit from highly accurate measurements, unprecedented speed and a compact form factor. More information.

The R&S®BBL200 is a liquide cooled broadband amplifier for high power application up to 10 kW P1dB in the frequency range of 9 kHz to 250 MHz.

The R&S®BBA150 is a robust broadband amplifier for EMC applications in the frequency range of 4 kHz to 6 GHz and rf output power up to 3000 W P1dB.

The TDR option displays discontinuities, reflection factors or impedance versus delay/length.

The FFT-based spectrum analysis function can be used to measure a DUT's spurious and harmonics, providing short sweep times along with high dynamic range and fine frequency resolution. It quickly detects undesired signal components (spurious) in converters and T/R modules. The marker-to-spectrumfunction directly gets to the root of problems in the event of unexpected S-parameter results, thus providing fast and extremely useful integrated diagnostics.

Noise figure measurement with vector network analyzers

VNA Source Phase Control Options for characterization of devices requiring a defined phase such as differential amplifiers, mixers, IQ mixers and others.

Options for characterizing frequency-converting devices such as mixers, block upconverters and downconverters, T/R modules and others.

Series of automatic economy calibration units with frequencies up to 50 GHz. 2 and 4 port models available. ZN-Z51 has configurable test ports.