RF performance and coverage of IoT devices

RF performance and coverage of IoT devices

Verify the RF performance of your IoT devices with smart test solutions to ensure safe operation, even under difficult conditions.

Wireless IoT devices operate for years and can easily be installed anywhere. New applications can mean that these devices have to be used in very difficult RF environments. Smart meters installed in basements, for example, have to handle tough coverage conditions. Robots on the factory floor have to deal with very harsh radio conditions while maintaining reliable, low latency communication. Other devices such as connected mousetraps or parking lot sensors need to be very robust and waterproof, which is challenging for the overall RF design. The RF performance of IoT devices wireless connections is a crucial factor for the success of IoT applications. Otherwise, there could be a direct impact on critical performance parameters like reliability, power consumption, latency and coverage.

Best in class RF performance call for smart testing

Thanks to the availability of a large variety of easy-to-use development platforms, it is quite simple to build a prototype of a wireless IoT device and run a proof of concept. But the RF design requires special attention. Factors like the used antenna, matching networks, housing, ground planes and surrounding components could have a large impact on the RF performance. Extensive experience in RF design and simulation tools will help, but ultimately the design needs to be verified under real-world conditions with an appropriate test setup.

Your IoT test challenges

IoT device measurements typically start with RF power, spectrum and receiver sensitivity measurements in connected mode. S-parameters are measured to verify and tune the antenna performance of the IoT device. After this, over-the-air measurement of the total radiated power (TRP) and total isotropic sensitivity (TIS) of the final design is recommended. Depending on the application, it can also be relevant to perform measurements under certain fading conditions or apply coverage enhancement techniques such as those used for NB-IoT and LTE-M devices.

Benefits of Rohde & Schwarz IoT test solutions

  • Compact solutions to measure the IoT RF performance of wireless IoT technologies
  • Comprehensive over-the-air test solutions, including desktop anechoic chambers that are suitable for most IoT applications
  • Wide range of oscilloscopes for testing all aspects of embedded designs, including power rails, interference and EMI.

Related resources

IoT design guide

eGuide: IoT design guide

More information

What is next in cIoT?

Webinar: What is next in cellular IoT and how can we test it?

OTA Measurements of LTE MIMO-Enabled Devices
Webinar: OTA measurements of LTE MIMO-enabled devices
White paper: LTE UE receiver performance measurements

White paper: LTE UE receiver performance measurements

More information

Related products

R&S®ZNH full two-port handheld vector network analyzer

R&S®ZNH full two-port handheld vector network analyzer

Offers one-port antenna measurement and full two-port S-parameter measurements.

Product information

R&S®FPC spectrum analyzer

R&S®FPC spectrum analyzer

Unexpected performance in entry class including one-port vector network analyzer functionality.

Product information

R&S®ZNLE vector network analyzer

R&S®ZNLE vector network analyzer

The ideal choice for basic vector network analyzer applications.

Product information

R&S®CMQ500 shielding cube

R&S®CMQ500 shielding cube

Optimized over-the-air test system for 5G FR1 and FR2 tests.

Product information

R&S®TS7124M RF shielded box

R&S®TS7124M RF shielded box

Enables reliable and reproducible measurements when a shielded test environment is needed.

Product information

R&S®DST200 RF diagnostic chamber

R&S®DST200 RF diagnostic chamber

Ideal environment for RF analysis during development. Supports a wide range of radiated test applications for wireless IoT devices and fits on any workbench.

Product information

R&S®ATS1800C CATR based compact 5G NR mmWave test chamber

R&S®ATS1800C CATR based compact 5G NR mmWave test chamber

3GPP-compliant, transportable and compact CATR test chamber for 5G FR2

Product information

Related topics

IoT testing

IoT testing

More information

IoT power consumption testing

IoT power consumption testing

More information

RF performance and coverage of IoT devices

IoT device certification and qualification

More information

Request information

Do you have questions or need additional information? Simply fill out this form and we will get right back to you.

I want to receive information from Rohde & Schwarz via

Marketing permission

What does this mean in detail?

I agree that Rohde & Schwarz GmbH & Co. KG and the Rohde & Schwarz entity or subsidiary company mentioned in the imprint of this website, may contact me via the chosen channel (email or postal mail) for marketing and advertising purposes (e.g. information on special offers and discount promotions) related to, but not limited to, products and solutions in the fields of test and measurement, secure communications, monitoring and network testing, broadcast and media, and cybersecurity.

Your rights

This declaration of consent may be withdrawn at any time by sending an email with the subject "Unsubscribe" to news@rohde-schwarz.com. Additionally, a link to unsubscribe from future email advertisements is contained in each email sent. Further details on the use of personal data and the withdrawal procedure are set out in the Statement of Privacy.

Your request has been sent successfully. We will contact you shortly.
An error is occurred, please try it again later.