R&S®CompactTSVP | | 1 slot required |
Interfaces |
Control bus | | CompactPCI/PXI |
DUT connector (front) | | 2 × Mini D Ribbon (MDR) connectors 2 × SMB plug connectors |
Rear I/O connector | | CompactPCI connector, 110 pins |
Side connector | RS-485 | Semtec terminal strips (2.54 mm) |
Module features |
Front connectors |
DIGITAL A/B | 2 × Mini D Ribbon (MDR) connectors | 2 × 8 LVDM data I/O channels 2 × 1 LVDM general purpose I/O channels 2 × 1 LVDM clock I/O channel 2 × 2 LVTTL digital I/O channels |
CLK, TRIG | 2 × SMB connectors | 1 clock I/O channel, 1 trigger I/O channel |
LVDS channels (data input mode) |
DIGITAL A/B | | 2 × MDR connectors |
Input modes | half-duplex operation | LVDM with termination 100 Ω |
Difference input voltage | | max. ±600 mV |
Difference input threshold | | min. ±100 mV |
Input resistance | | 100 Ω |
Realtime acquisition | sample rate (SDR) | 0.01 bit/s to 100 Mbit/s (10 ns resolution) |
| sample rate (DDR) | 200 Mbit/s (only for data channels) |
LVDS channels (data output mode) |
DIGITAL A/B | | 2 × MDR connectors |
Output modes | half-duplex operation | LVDM with termination 100 Ω |
Output voltage | |VOD|, into 50 Ω load (double termination) | 247 mV (min.), 454 mV (max.) |
Output current | IOS | max. 10 mA |
Tristate control | | programmable per channel and up to 50 Mbit/s per sample |
Realtime stimulation | sample rate (SDR) | 0.01 bit/s to 100 Mbit/s (10 ns resolution) |
| sample rate (DDR) | 200 Mbit/s (only for data channels) |
TTL channels (input/output mode) |
DIGITAL A/B | | 2 × MDR connectors |
Input/output mode | voltage | 3.3 V logic; 10 kΩ pullup onboard |
Realtime stimulation/acquisition | sample rate | 0.01 bit/s to 50 Mbit/s (10 ns resolution) |
Connector | onboard connector | pin connector (terminal strips 2.54 mm) |
Input/output mode | | RS-485/422 signal level, 10 bidirectional channels, no RS-485 serial protocol |
Realtime stimulation/acquisition | sample rate | 0.01 bit/s to 20 Mbit/s with 10 ns resolution |
Realtime stimulation/acquisition memory | data buffer depth/width (programmable) | 2 M pattern at 32 bits (18 × LVDS, 4 × TTL, 10 × RS-485) |
External clock |
DIGITAL A/B | input/output voltage | according to LVDS channels, 2 × MDR connectors |
| frequency range | 20 MHz to 50 MHz |
CLK | input/output voltage | 3.3 V TTL logic (SMB plug) |
| frequency range | 20 MHz to 50 MHz |
Trigger |
TRIG | input/output voltage | 3.3 V TTL logic (SMB plug) |
PXI | input/output voltage | 8 x PXI, 5 V TTL logic |
Synchronization |
Trigger units | applications | 2 x fully independent hardware trigger logic ❙ programmable trigger generator ❙ generation of realtime stimulation clock ❙ generation of realtime acquisition clock ❙ frequency measurement |
Trigger unit characteristics | reference pattern | 10-bit, 3 states: high, low, don’t care |
| slope | positive/negative |
| trigger delay setting | 0 s to 100 s (10 ns resolution) |
| output signals | ❙ trigger received signal (pulse) ❙ trigger active signal (start of trigger until burst end) ❙ sample pulse (pulse for each sample) |
Synchronization inputs | channels | 1 × TTL trigger (TRIG) 8 × PXI trigger bus 1 × pattern comparator |
Synchronization outputs | channels | 1 × TTL trigger (TRIG) 8 × PXI trigger bus |
| signals | ❙ output, trigger unit 1 (IT1) ❙ output, trigger unit 2 (IT2) ❙ TTL signal (TRIG) |
General data |
Environmental conditions |
Power consumption | | 5 V: typ. 1 A, 3.3 V: typ. 1 A |
Temperature | operating temperature range | +5 °C to +40 °C |
| storage temperature range | –10 °C to +60 °C |
Damp heat | | +40 °C, 80 % rel. humidity, steady state, in line with EN 60068-2-30 |
Mechanical resistance |
Vibration | sinusoidal | 5 Hz to 55 Hz, 0.15 mm amplitude const., 55 Hz to 150 Hz, 0.5 g const., in line with EN 60068-2-6 |
| random | 10 Hz to 300 Hz, acceleration 1.2 g (RMS), in line with EN 60068-2-64 |
Shock | | 40 g shock spectrum, in line with MIL-STD-810E, method 516.4, procedure I |
Product conformity |
Electromagnetic compatibility | EU: in line with EMC Directive 2014/30/EC | applied harmonized standards: EN 61326-1: 2013 (industrial environment), EN 61326-2-1: 2013, EN 55011: 2009 + A1: 2010 Group 1, Class A |
Electrical safety | EU: in line with Low Voltage Directive 2014/35/EC | applied harmonized standard: EN 610110-1: 2010 |
Dimensions | W × H × D | 316 mm × 174 mm × 20 mm (12.4 in × 6.8 in × 0.8 in) |
Weight | | 0.21 kg (0.47 lb) |