74 Results
The R&S CMP180 offers a frequency range up to 8 GHz and a bandwidth up to 500 MHz and enables simultaneous testing of multiple DUTs supporting cellular technologies up to 5G NR-FR1 and non-cellular technologies such as Bluetooth and Wi-Fi and many more. CMP180, 5G Wi-Fi 7 (IEEE 802.11be) 4x4 true-MIMO testing
09-Nov-2020
New Rohde & Schwarz System Amplifier Targets Microwave Device ManufacturersSAM100 targets manufacturers of passive and active microwave components and microwave devices for mobile radio (UMTS, LTE, 4G & 5 G), IoT (WLAN, Bluetooth), satellite and radar applications.
27-Oct-2021
China Mobile purchases R&S SMM100A vector signal generator for 5G testingRecently, China Mobile has selected the R&S SMM100A vector signal generator from Rohde & Schwarz to validate its 5G technology. The new signal source generates 5G signals in research applications to verify current and future 5G technologies. The project is a continuation of the long term cooperation between China Mobile and Rohde & Schwarz China.
To ensure connectivity and trouble-free operation, each Bluetooth® enabled device has to be tested for conformance with Bluetooth SIG standards and regulatory requirements.
23-Nov-2017
This document describes Bluetooth Low Energy RF over-the-air RX and TX measurements using advertising channels for communication with Bluetooth Low Energy devices.
14-Dec-2020 | AN-No. 1C109
Bluetooth® Low Energy channel sounding validation
06-Sep-2023
This application note describes how to use the R&S CMW platform to perform the measurements defined in Bluetooth test specification version 5.
19-Jun-2017 | AN-No. 1MA282
This document describes the direct test mode mechanisms for testing Bluetooth Low Energy devices and explains how the direct test mode connection is established. The R&S CMW uses a USB port for the direct test mode connection while the Equipment under Test (EUT) may provide a USB port, a serial port or even a 2-wire UART interface for this purpose. Installing or assigning the right driver for the EUT is the main configuration task on the R&S CMW. For EUTs with USB port, the R&S CMW provides a Bluetooth Low Energy USB driver which has to be assigned to the connected EUT.
14-Dec-2016 | AN-No. 1C105
Transmitter and Receiver Measurements on Bluetooth Modules with CMU200
06-Aug-2001 | AN-No. 1MA46
This document describes the adaptive frequency hopping mechanism for improved signaling performance in Bluetooth Basic Rate and Enhanced Data Rate devices.The R&S CMW provides this feature for remote operation in TX, Loopback and Connection test mode. Thereby the R&S CMW acts as a master, while the Equipment under Test (EUT) represents the slave(s) of the piconet.
14-Dec-2016 | AN-No. 1C108
The R&S®CMW wireless communication tester are ideal for designing and verifying Bluetooth® Low Energy (LE) circuits and modules.
27-Jan-2017
Bluetooth Transmitter Measurements without Connection Setup
04-Feb-2003 | AN-No. 1MA49
Measurements on Bluetooth Devices using R&S CMU200 and CMUgo
06-Oct-2006 | AN-No. 1CM50
The Rohde & Schwarz Bluetooth RF test solution with the R&S CMW and R&S CMWrun is closely aligned to the Bluetooth RF Test Suite. This document describes common setups for these tests and the required configurations.
04-May-2015 | AN-No. 1MA261
Generating Bluetooth RF Test Signals with SMIQ Signal Generator
30-Jan-2001 | AN-No. 1MA31
09-Nov-2021
Rohde & Schwarz joins Car Connectivity Consortium to support development of smartphone-to-car communications including UWBRohde & Schwarz has joined the Car Connectivity Consortium (CCC) to support the organization's mission to foster industrywide standards for communications between vehicles and smartphones. The company will contribute its broad expertise in mobile device and automotive technology testing. In particular, the company will provide its solutions for the development and production of UWB devices and modules for automotive applications such as keyless vehicle access.
13-Oct-2020
Rohde & Schwarz propels 5G LBS with Assisted-GPS and 5G NR FR2 mmW performance testingAs wireless network operators roll out 5G NR in the millimeter wave spectrum, it is critical to ensure continued reliability of E911 calls and accurate determination of location in mobile devices.
Smartly verify and decode Bluetooth® Low Energy (BLE) transmit signals with a reliable and costefficient spectrum analyzer – the R&S®FPC.
17-May-2018
This application note gives the guidance of how to perform the BLE 5.1 DF RF tests according to the RF test specification of BT 5.1 by using the Rohde & Schwarz test solutions.
30-Oct-2019 | AN-No. GFM327
This is especially important for applications such as Bluetooth hands-free calling and eCall. The process starts accurately measuring speech quality over a 5G connection in a lab environment, such as the HEAD acoustics facility in Aachen, Germany.
This application note describes the tests performed with additional equipment and presents straightforward solutions based on the R&S®CBTgo software.
18-Jul-2013 | AN-No. 1MA200
An automated test solution based on the R&S®CMW wideband radio communication tester fully supports the new test cases for real-time submeter positioning.
10-Jun-2022
Unplug Bluetooth Low Energy testing reinvented - Flyer
This application note describes the tests performed with additional equipment and presents straightforward solutions based on the CBTgo software.
06-Mar-2013 | AN-No. 1MA106
This document provides the technical specifications of the R&S®FSx-K8 Bluetooth® measurement application.
This application note employs preliminary theoretical analysis and demonstrates how the problems of indevice coexistence can be measured.
28-Apr-2015 | AN-No. 1MA255