74 Results
To ensure connectivity and trouble-free operation, each Bluetooth® enabled device has to be tested for conformance with Bluetooth SIG standards and regulatory requirements.
23-Nov-2017
This document describes Bluetooth Low Energy RF over-the-air RX and TX measurements using advertising channels for communication with Bluetooth Low Energy devices.
14-Dec-2020 | AN-No. 1C109
Bluetooth® Low Energy channel sounding validation
06-Sep-2023
This application note describes how to use the R&S CMW platform to perform the measurements defined in Bluetooth test specification version 5.
19-Jun-2017 | AN-No. 1MA282
This document describes the direct test mode mechanisms for testing Bluetooth Low Energy devices and explains how the direct test mode connection is established. The R&S CMW uses a USB port for the direct test mode connection while the Equipment under Test (EUT) may provide a USB port, a serial port or even a 2-wire UART interface for this purpose. Installing or assigning the right driver for the EUT is the main configuration task on the R&S CMW. For EUTs with USB port, the R&S CMW provides a Bluetooth Low Energy USB driver which has to be assigned to the connected EUT.
14-Dec-2016 | AN-No. 1C105
Transmitter and Receiver Measurements on Bluetooth Modules with CMU200
06-Aug-2001 | AN-No. 1MA46
This document describes the adaptive frequency hopping mechanism for improved signaling performance in Bluetooth Basic Rate and Enhanced Data Rate devices.The R&S CMW provides this feature for remote operation in TX, Loopback and Connection test mode. Thereby the R&S CMW acts as a master, while the Equipment under Test (EUT) represents the slave(s) of the piconet.
14-Dec-2016 | AN-No. 1C108
The R&S®CMW wireless communication tester are ideal for designing and verifying Bluetooth® Low Energy (LE) circuits and modules.
27-Jan-2017
Bluetooth Transmitter Measurements without Connection Setup
04-Feb-2003 | AN-No. 1MA49
Measurements on Bluetooth Devices using R&S CMU200 and CMUgo
06-Oct-2006 | AN-No. 1CM50
The Rohde & Schwarz Bluetooth RF test solution with the R&S CMW and R&S CMWrun is closely aligned to the Bluetooth RF Test Suite. This document describes common setups for these tests and the required configurations.
04-May-2015 | AN-No. 1MA261
Generating Bluetooth RF Test Signals with SMIQ Signal Generator
30-Jan-2001 | AN-No. 1MA31
Smartly verify and decode Bluetooth® Low Energy (BLE) transmit signals with a reliable and costefficient spectrum analyzer – the R&S®FPC.
17-May-2018
This application note gives the guidance of how to perform the BLE 5.1 DF RF tests according to the RF test specification of BT 5.1 by using the Rohde & Schwarz test solutions.
30-Oct-2019 | AN-No. GFM327
This application note describes the tests performed with additional equipment and presents straightforward solutions based on the R&S®CBTgo software.
18-Jul-2013 | AN-No. 1MA200
The R&S CMP180 offers a frequency range up to 8 GHz and a bandwidth up to 500 MHz and enables simultaneous testing of multiple DUTs supporting cellular technologies up to 5G NR-FR1 and non-cellular technologies such as Bluetooth and Wi-Fi and many more. CMP180, 5G Wi-Fi 7 (IEEE 802.11be) 4x4 true-MIMO testing
An automated test solution based on the R&S®CMW wideband radio communication tester fully supports the new test cases for real-time submeter positioning.
10-Jun-2022
Unplug Bluetooth Low Energy testing reinvented - Flyer
This application note describes the tests performed with additional equipment and presents straightforward solutions based on the CBTgo software.
06-Mar-2013 | AN-No. 1MA106
09-Nov-2020
New Rohde & Schwarz System Amplifier Targets Microwave Device ManufacturersSAM100 targets manufacturers of passive and active microwave components and microwave devices for mobile radio (UMTS, LTE, 4G & 5 G), IoT (WLAN, Bluetooth), satellite and radar applications.
This document provides the technical specifications of the R&S®FSx-K8 Bluetooth® measurement application.
This application note employs preliminary theoretical analysis and demonstrates how the problems of indevice coexistence can be measured.
28-Apr-2015 | AN-No. 1MA255
Conducted multistandard in-device coexistence testing - ApplicationCard
19-Feb-2018
27-Oct-2021
China Mobile purchases R&S SMM100A vector signal generator for 5G testingRecently, China Mobile has selected the R&S SMM100A vector signal generator from Rohde & Schwarz to validate its 5G technology. The new signal source generates 5G signals in research applications to verify current and future 5G technologies. The project is a continuation of the long term cooperation between China Mobile and Rohde & Schwarz China.
Bluetooth(TM) qualification in development and quality assurance
Bluetooth(TM) Analysis Software Option (OPT.66) - Specifications