Download Center

The non-cellular expert covering WLAN, Bluetooth®, GNSS and various broadcast technologies. The R&S ® CMW270 is a cost-effective alternative for the development and production of equipment outside the conventional cellular networks, specially prepared for the test requirements of IoT (Internet of Things) market.

The R&S®CMW wideband radio communication tester offers universal, efficient test solutions for all modern cellular and non-cellular standards. The R&S®CMW is the world’s most widely used T&M platform for development, production and service. It meets all of the requirements for a state-of-theart wireless communication tester. The R&S®CMW can also emulate network operation under realistic conditions for protocol and RF tests.

This white paper introduces a novel attribute based architecture for VXIplug&play instrument drivers. The presented architecture uses the attribute based concept of IVI-C instrument drivers to introduce a two-layer design for VXIplug&play instrument drivers. Moreover the use of attributes is shown for the Rohde & Schwarz Spectrum Analyzer (rsspecan) instrument driver.

01-Dec-2012 | AN-No. 1MA170

For establishing a WLAN connection between R&S®CMW and device under test (DUT), the WLAN properties at the R&S®CMW have to be adapted to the test conditions. These can vary in several aspects, particularly due to the different WLAN standards and characteristics of the DUT. This document describes the critical parameters and provides step-by-step procedures for the configuration.

08-Dec-2015 | AN-No. 1C106

IoT devices have tight requirements for power consumption in order to achieve expected battery life times of multiple years without a connection to a power supply. In order to verify the power consumption and expected battery life time, voltage and current have to be measured accurately for different operating states of the device under test.This application note explains battery life tests using RT-ZVC in combination with CMWrun and CMW500, including example applications.The solution by Rohde & Schwarz enables precise voltage, current and consequently, power measurements.The RT-ZVC Multi-Channel Power Probe can be driven as part of a test plan combining signaling and power measurements for a detailed view of the power consumption in different signaling states as well as an estimation of overall lifetime given a certain battery capacity.

17-Feb-2017 | AN-No. 1MA281

The Rohde & Schwarz Bluetooth RF test solution with the R&S®CMW and R&S®CMWrun is closely aligned to the Bluetooth RF Test Suite. Most of the tests can be performed with the equipment under test connected to a single CMW which is remotely controlled via R&S®CMWrun running on an external computer. Some of the tests require an additional signal generator. This document describes common setups for these tests and the required configurations.

04-May-2015 | AN-No. 1MA261

Rohde & Schwarz – recognized as a reliable partner for WLAN testing solutions: As a leading supplier of T&M solutions for the wireless communications market, Rohde & Schwarz offers the R&S®CMW wideband radio communication tester, a universal, flexible platform for all major cellular and non‑cellular standards. The R&S®CMW measures the RF characteristics of transmitters and receivers on the air interface of wireless devices. It evaluates the applications and performance, and analyzes the protocol stack.

This document describes the adaptive frequency hopping mechanism for improved signaling performance in Bluetooth Basic Rate and Enhanced Data Rate devices.The R&S CMW provides this feature for remote operation in TX, Loopback and Connection test mode. Thereby the R&S CMW acts as a master, while the Equipment under Test (EUT) represents the slave(s) of the piconet.

14-Dec-2016 | AN-No. 1C108

This document describes the direct test mode mechanisms for testing Bluetooth Low Energy devices and explains how the direct test mode connection is established. The R&S CMW uses a USB port for the direct test mode connection while the Equipment under Test (EUT) may provide a USB port, a serial port or even a 2-wire UART interface for this purpose. Installing or assigning the right driver for the EUT is the main configuration task on the R&S CMW. For EUTs with USB port, the R&S CMW provides a Bluetooth Low Energy USB driver which has to be assigned to the connected EUT.

14-Dec-2016 | AN-No. 1C105

This document describes how a Windows®-based R&S® T&M instrument is remotely operated by an Apple iPad as if working on it locally. Step-by-step procedures are provided for setting up and configuring the T&M instrument and the iPad. On the iPad, a special App implements the Windows® 'Remote Desktop' functionality. T&M instrument and iPad are connected via WLAN (also denoted as Wi-Fi network).

28-Mar-2013 | AN-No. 1MA216