30-Jan-2025 | Press Releases | MWC 2025

At MWC Barcelona 2025, Rohde & Schwar will present a diverse portfolio themed “Enabling Connections, Empowering Innovations” aimed at assisting industry leaders and visionaries turn their ideas for new mobile technologies, products, and applications into reality.

This document provides the technical specifications of the R&S®RT-Zxx high voltage and current probes.

This application note summarizes the Rohde &Schwarz test solutions for LTE-Advanced (Release 10) using Vector Signal Generators, Signal and Spectrum Analyzers and the Wideband Radio Communication Tester.

03-Sep-2014 | AN-No. 1MA166

Explore comprehensive DDR testing solutions from Rohde & Schwarz for signal integrity and compliance testing across all generations of DDR technology.

PAM-N Analysis with the R&S RTP Oscilloscope (Part 3) Learn about key advantages of the PAM-N analysis option on the R&S RTP & RTO6 oscilloscopes together with the Advanced Eye option to characterize and verify signal transitions.

PAM-N Analysis with the R&S RTP Oscilloscope (Part 2) Learn about key advantages of the PAM-N analysis option on the R&S RTP & RTO6 oscilloscopes. In combination with the CDR option, obtain the fastest eye diagrams to characterize signal behaviour in seconds.

This document provides an introduction to SDR as used for military radios and presents the relevant T&M solutions offered by Rohde & Schwarz.

15-Sep-2012 | AN-No. 1MA206

This application note shows developers and manufacturers of devices with LoRa wireless technology how transmitter measurements are conducted in line with FCC Part 15.247.

29-Nov-2017 | AN-No. 1MA295

Based on the new high-performance R&S®SMW200A vector signal generator and the R&S®RTO digital oscilloscope, the solution provides MIMO signal generation and realtime channel emulation (up to 4x4 or 8x2) as well as synchronous analysis of multiple TX antenna signals.

Compliance Testing, maximum output droop, RTO, Test Mode 6 A guide to carrying out a 100BASE-T1 compliance test for the MDI return loss using an R&S®ZND 2-port vector network analyser controlled by the ScopeSuite automation software.

R&S®VISA is a standardized software library that allows fast communications over diverse interfaces with a wide variety of T&M instruments that are detected on the network from PC applications.

26-May-2020 | AN-No. 1DC02

R&S RT-ZPR20 Accurate and fast power integrity measurements - Application Card

The radio unit activity versus power consumption is monitored using the R&S RTO oscilloscope to detect short power pulses or spikes. The results make it easy to evaluate energy efficiency measures such as advanced sleep modes and provide ratings for radio units based on their power consumption.

Versatile Software Tool for Rohde & Schwarz Instruments

RSCommander is a versatile software tool for a wide range of Rohde & Schwarz spectrum-, network analyzers, signal generators and oscilloscopes. It allows for automatic instrument discovery, making screenshots, reading traces, file transfer and simple script creation.

24-Dec-2017 | AN-No. 1MA074

Unique trigger capability Unique trigger capability Video, RTO2000, Oscilloscope, Triggering Unique trigger capability

Learn how to debug serial protocols with an oscilloscope. Explore the most common types of serial protocols, such as UART, (Q)SPI, I2C and CAN bus.

Easy configuration of frequency domain analysis Easy configuration of frequency domain analysis Video, RTO2000, Oscilloscope, Responsive FFT and spectogram Easy configuration of frequency domain analysis

How to perform signal integrity debugging on a DDR3 device Video, RTO2000, Oscilloscope, DDR3 DDR3 signal integrity debugging

Rohde & Schwarz Drivers under VEE - Installation and Troubleshooting

20-Dec-2012 | AN-No. 1MA035

This white paper describes how a QAgent deployment might be handled to lessen the impact on production or lab environments.

Oscilloscope bus decoding, RTO2000, bus decoding, I2C Dive into your protocol to check for any problems with your I²C interface.

This Application Note addresses signal measurements and analysis of automotive radars that are crucial during the development and verification stages.

10-Jun-2016 | AN-No. 1MA267

This document is divided in two parts and starts with an introduction in AC-DC conversion principles in general. It will present the most common circuits used for different power levels. The switching mode power supply (SMPS) converter will be the main focus as they are used everywhere in the electronics. Especially the flyback converter design in different flavors are highlighted. Nevertheless, all measurements are also applicable for other SMPS converter designs operating at higher power levels.In the second part of this document, most relevant testing methods and procedures of an AC-DC converter are highlighted. For each testing section, a fundamental part will be upfront discussed and it is followed by a presentation of a suitable measurement method. In this second part, the device under test (DUT) is considered as black box device and thus the structure is similar. Therefore, the testing parts consists of methods related to input tests, output tests and a combination of both like efficiency. Of course, some test performed at the output of the converter are also relevant for DC-DC converter, e.g. the validation of the output ripple.

14-Nov-2022 | AN-No. 1SL387

Discover some of the key parameters of an oscilloscope and how they impact on the performance in this video series: Part 1: Bandwidth and frequency response R&S®RTO2000 Video, application videos, oscilloscope, troubleshooting, mixed signal oscilloscope R&S Talking about bandwidth Open Lightbox Talking about bandwidth

Discover leading test solutions for network energy saving. Explore how to reduce RAN power consumption and increase the efficiency of Open RAN radio units.

The R&S®RTO-K92 eMMC Compliance Test option offers an automated test solution for the electrical interface of an eMMC device according to the JEDEC specification, revision 5.1. Oscilloscope Application Videos, Application Video, Application Videos, Videos, eMMC Interface Compliance Test Learn how you can use the eMMC compliance test of R&S for automated testings of electrical interfaces!

RTO2000, debugging, EMI When debugging EMI problems in electronic circuits, development engineers face the challenging problem of quickly and accurately identifying and eliminating the sources of unwanted emissions. Many problems can be eliminated during development by using oscilloscopes for EMI debugging.

Oscilloscope bus triggering, RTO2000, bus triggering, history mode, break condition Use the hardware trigger to isolate break conditions. Break conditions can be corellated with their root cause one by one using the History Mode.

Generating models with a VNA and using these on an oscilloscope via the deembedding

23-May-2023 | AN-No. 1SL393

RTO2000, waveform display, R&S®SmartGrid, complex measurements Use the R&S®SmartGrid function to configure the display. For complex measurement tasks where several screen displays are helpful, you can superposition windows in multiple tabs. All measurement diagrams have labeled scales so you can immediately read important signal characteristics.