7 Results
The present R&S®SMW-K506 Interface Control Document contains information on► the R&S descriptor word format, including ARB descriptor words and control descriptor words in deterministic and instant mode► Timing requirements and limitations of the interface► Properties of the network interface (Connector designation: HS DIGIQ).It is intended for use by customers using descriptor words to control the R&S®SMW200A in real-time. The interface control document specifies the interface between the customer’s hardware used for provision of descriptor words and the R&S®SMW200A HS DIGIQ interface. Additional information on descriptor word processing inside the R&S®SMW200A is provided.
17-Mar-2022 | AN-No. 1GP134
EW receivers are tested in the lab at RF to discover problems before flight testing. This eliminates cost and schedule risk. Flight testing can cost tens of thousands of dollars per hour and must be scheduled many months in advance. In contrast, using test equipment to test at RF might require a certain upfront cost but provides a readily-accessible capability to simulate radar threats at RF for a long time. This application note explains how the angle-of-arrival (AoA) capabilities of EW receivers can be tested with commercial off-the-shelf (COTS) RF test equipment. Topics covered are the generation of scenarios, instrument setup, and setup calibration. We will use a radar warning receiver (RWR) as a proxy for a generic EW receiver in this application note.
22-Dec-2021 | AN-No. 1GP125
The present R&S®SMW-K503/-K504 Interface Control Document contains information on- the R&S descriptor word format, including pulse descriptor words and timed control descriptor words in basic and expert mode- Timing requirements and limitations of the real-time control interface- Properties of the ADV DATA/CTRL network interfaceIt is intended for use by customers using descriptor words to control the R&S®SMW200A in real-time. The interface control document specifies the interface between the customers hardware used for provision of descriptor words and the R&S®SMW200A ADV DATA/CTRL interface. Additional information on descriptor word processing inside the R&S®SMW200A is provided.
25-Aug-2021 | AN-No. 1GP133
EW receiver mission data files can contain hundreds of emitters with thousands of modes and beams that must be tested by simulation at RF. Often, these emitters, their modes and beams are listed on intelligence databases and must be imported from a spreadsheet into to an emitter simulation application such as the R&S®Pulse Sequencer software. For this purpose, the R&S®Pulse Sequencer software offers an internal script editor which allows to import user data and automatically generate emitter, sequence or platform configurations that can then immediately be played into RF without any additional software. Furthermore, the R&S®Pulse Sequencer offers a SCPI recorder tool to collect manual entries during scenario data creation into a list of corresponding SCPI commands. This list of commands can easily be used to create user defined scripts that can either run in the internal script editor or an external software (e.g. Matlab, Python).
01-Jul-2021 | AN-No. 1GP131
This application note belongs to a series of application notes which explains how to test EW receivers at RF in the lab with commercial, off-the-shelf signal generators and software. The series will cover all relevant use cases. This application note will discuss threat simulation and verification. Further application notes will address calibration and verification of multi-channel setups for simulation of angle of arrival, generation of radar signals in a hardware in the loop (HIL) environment with PDW Streaming, and automated threat creation and sequencing.
23-Mar-2021 | AN-No. 1GP123
Development of modern EW systems is a complex and expensive process, that requires thorough testing against all requirements during all phases of development. To keep cost under control, system level testing in the lab is key and brings several advantages: test cases can be reproduced under the exact same conditions as often as necessary. System level testing in the lab is often performed in a hardware-in-the-loop (HIL) environment. This application note provides some insight into generating radar signals for hardware-in-the-loop testing with the R&S®SMW200A. An introduction to HIL testing and realtime operation of the R&S®SMW200A is given. The hardware and software interface, the PDW format and synchronization and timing mechanisms are described. Additionally, various example scenarios and detailed information about intermediate calculations are provided. The application note also provides information about system requirements for advanced PDW streaming with multiple emitters on multiple parallel streams.
22-Jan-2021 | AN-No. 1GP124
The need to properly represent the ever changing complexities of the RF environment across communications, surveillance, electronic support measures (ESM) and signal intelligence system (SIGINT) with the advances of signal complexity and bandwidth, requires an enormous test and measurement effort.Extensive field tests are often applied to verify the performance and capabilities under preferably natural but controlled conditions. This is both costly and requires a great deal of time.RF signal environment generation using Test & Measurement equipment brings field tests into the laboratory, where a controlled, cost-effective and reproducible environment exists. The R&S®Pulse Sequencer software is a versatile tool to generate arbitrary and realistic RF signal scenarios ensuringsystem readiness for the real operational world.This application note introduces the R&S®Pulse Sequencer software, explains several examples that are applicable for research, development, before operational and during life-time test in detail, and guides you through the necessary steps, to generate a self-defined, arbitrary real life RF signal environment.
17-Jan-2017 | AN-No. 1MA288