Mobile network testing blog

Stories & insights

Mobile network testing

Written by Manuel Mielke | July 20, 2017

NB-IoT: Scanners are a must for coverage measurements (part 2)

In part 1 of our series about NB-IoT, an “Overview of Internet of Things technologies with a focus on NB-IoT”, we described typical use cases and current technologies of the Internet of Things (IoT). We also identified that networks for IoT applications would be optimized for the highest availability, particularly concerning IoT applications under extreme receive conditions such as smart meters in basements. Consequently, operators who are planning and deploying new NB-IoT networks will inevitably face the coverage challenge.

NB-IoT: Scanners are a must for coverage measurements

There are different means to measure network coverage: active and passive. To identify if an NB-IoT service is provided by the network, simply turn on your NB-IoT user equipment. If it can find a serving cell, then service is provided, and the RF coverage can be measured. However, NB-IoT user equipment is limited in mobility, and the measurement results are therefore bound to be incomplete, if not inconclusive. We call this approach active because it interacts with the NB-IoT network. A valid subscription for NB-IoT services and a SIM card are required for active NB-IoT coverage measurements.

Scanners for accuracy and true coverage information

A much more accurate and reliable means of network coverage identification is a network scanner. The radio receiver is a passive device that captures the measurement data directly from the RF air interface. Instead of limiting measurements to one particular operator’s cell via a serving cell selection procedure, the passive scanner-based approach enables the capture of data from all operators and all available cells in an NB-IoT network.

The most significant parameters include power levels and signal-to-noise ratios of the different signals in the NB-IoT radio frame. Those parameters allow drawing conclusions about the RF conditions at a certain location, which provide the basis for network access through NB-IoT devices.

Scanner information is crucial for key tasks

A scanner is the only tool that can provide real coverage information. This information is crucial for completing three main tasks:

Network planing: Particularly in the early phases of an NB-IoT rollout, network planning tools need to “learn” so as to be optimally tuned to provide reliable planning data.

Troubleshooting: In general, if network performance is low (QoS), then troubleshooting helps to identify the root cause. With NB-IoT, however, troubleshooting reaches a new level of complexity. Say, the connection to a network device is lost or goes through retransmission. While troubleshooting, RF conditions will be given priority.

For example, finding an interference source requires an in-depth investigation of other technologies located closely within the spectrum. With the multi-technology capability of scanners, other technologies, such as GSM, (W)CDMA, or LTE, that have an impact on NB-IoT networks can be evaluated.

Especially in-band and guard-band operation mode, often used for efficiently implementing the NB-IoT signal into the spectrum, lead to spectrum constellations without any gaps or guard-bands between the NB-IoT carrier and the available LTE air interface (i.e., physical resource blocks). Consequently, interference with adjacent LTE resource blocks must be taken into account.

Benchmarking: Benchmarking is an essential task in testing mobile networks. Just like any other mobile network, also NB-IoT networks from different operators should be compared and evaluated to find the best NB-IoT coverage for certain regions. With the limitations of NB-IoT user equipment in mind, it becomes obvious that only network scanners command the completion of such demanding tasks. Connection reliability is more critical for NB-IoT than for LTE. Because unlike human beings, a smart meter in a below-ground indoor environment cannot change position and search for better coverage.

Why coverage measurements with user equipment are insufficient

As discussed earlier, user equipment-based measurements are active, requiring access to an operators’ NB-IoT network services using valid subscriptions. Compared to scanner measurements, they are limited, and hence inconclusive. The reason being that NB-IoT user equipment does not support full mobility as we are used to in legacy LTE.

To reduce the complexity and cost of NB-IoT chipsets, 3GPP has limited the mobility to idle mode only with cell reselection measurements. This means that neighbor cell measurements can only occur in idle mode, and once the NB-IoT device is in connected mode, it stops searching for neighbored cells.

Once connected to a cell and actively transferring data, the NB-IoT user equipment will remain on this particular cell until the connection is lost while driving. After that, the NB-IoT user equipment will start searching for a better cell and initiate cell reselection. Since NB-IoT user equipment cannot measure signals from more than the serving cell in connected mode, a better signal than the current one will not be recognized.

As a result, user equipment-based measurements are limited to one specific network and impaired by different behaviors and by the test script sequence influence on the connection state. Drive tests conducted with NB-IoT user equipment doing active data transfers miss a certain amount of data during the segments in connected mode, which leads to incorrect coverage drive-testing results.

A huge number of NB-IoT modules and chipsets can be found on the market, all showing different RF characteristics. Compared to NB-IoT user equipment-based measurements, scanner measurements offer a clear view of the RF conditions at a certain location. They provide reference measurements that are unaffected by the devices’ RF parts and cell-reselection behaviors.

Test solution for NB-IoT networks

Scanner measurements show all available NB-IoT cells independent of their spectrum implementation and RF parameters, which allows real coverage evaluation. The screenshot shows a coverage plot from a drive test of about 20 km, conducted during field trials in China earlier this year.

Drive test coverage plot with all available NB-IoT cells
Drive test coverage plot with all available NB-IoT cells

With our R&S®TSMx scanners and R&S®ROMES4 drive test software, any measurement environment is easy to handle and optimized for drive and walk testing. The ultra-compact and lightweight measurement hardware with well-adapted carrying bags and backpacks with battery operation are optimally tailored for indoor walk testing. Especially in NB-IoT networks, coverage will be all about indoor availability with, say, smart power meters located in the basement.

R&S®TSME scanner from the R&S®TSMx network scanner family
R&S®TSME scanner from the R&S®TSMx network scanner family
R&S®TSMx scanner with R&S®ROMES4 drive test software
R&S®TSMx scanner with R&S®ROMES4 drive test software

Read part 3 of this series about using NB-IoT user equipment as the data collection device here.

Related stories

NB-IoT: How to find NB-IoT carriers in the spectrum (part 6)

NB-IoT: How to find NB-IoT carriers in the spectrum (part 6)

Read more

NB-IoT field test: Measuring NB-IoT underground

NB-IoT field test: Measuring NB-IoT underground

Read more

5G measurements to lay the foundation for autonomous vehicles in port terminals

5G measurements to lay the foundation for autonomous vehicles in port terminals

Read more

Subscribe MNT blog

Sign up for our newsletter

Stay up to date and get stories and insights with our frequent mobile network testing newsletter.

Stories by category

Benchmarking & optimization
Benchmarking & optimization

More information

Field services & interference hunting
Field services & interference hunting

More information

Innovations in mobile network testing
Innovations in mobile network testing

More information

Testing from RF to QoE
Testing from RF to QoE

More information

Request information

Do you have questions or need additional information? Simply fill out this form and we will get right back to you.

I want to receive information from Rohde & Schwarz via

Marketing permission

What does this mean in detail?

I agree that Rohde & Schwarz GmbH & Co. KG and the Rohde & Schwarz entity or subsidiary company mentioned in the imprint of this website, may contact me via the chosen channel (email or postal mail) for marketing and advertising purposes (e.g. information on special offers and discount promotions) related to, but not limited to, products and solutions in the fields of test and measurement, secure communications, monitoring and network testing, broadcast and media, and cybersecurity.

Your rights

This declaration of consent may be withdrawn at any time by sending an email with the subject "Unsubscribe" to news@rohde-schwarz.com. Additionally, a link to unsubscribe from future email advertisements is contained in each email sent. Further details on the use of personal data and the withdrawal procedure are set out in the Statement of Privacy.

Your request has been sent successfully. We will contact you shortly.
An error is occurred, please try it again later.