7952 Results
The amendment 802.11ad to the WLAN standard defines the MAC and PHY layers for very high throughput (VHT) in the 60 GHz range. This application note provides a brief examination of key 802.11ad parameters, describes the required measurements and test setups and contains several important recommendations for over-the-air (OTA) measurements.
17-May-2017 | AN-No. 1MA260
Learn more about the R&S®SFC and how it supports all conventional digital and analog TV and audio broadcast standards.
19-Feb-2015
This document describes the direct test mode mechanisms for testing Bluetooth Low Energy devices and explains how the direct test mode connection is established. The R&S CMW uses a USB port for the direct test mode connection while the Equipment under Test (EUT) may provide a USB port, a serial port or even a 2-wire UART interface for this purpose. Installing or assigning the right driver for the EUT is the main configuration task on the R&S CMW. For EUTs with USB port, the R&S CMW provides a Bluetooth Low Energy USB driver which has to be assigned to the connected EUT.
14-Dec-2016 | AN-No. 1C105
The R&S®RTO digital oscilloscope analyzes RF pulses up to the maximum bandwidth of the instrument used.
09-Nov-2017
This Application Note gives a short overview how signals with two different modulation schemes can be analyzed using the R&S®FSW.
18-Apr-2016 | AN-No. 1EF93
High sampling rate and automatic pulse analysis make the R&S®NRP-Z8x wideband power sensor family ideal for time-domain analysis of radar pulses.
06-Aug-2013
This application note demonstrates the use of the FSMR, including the Cross-correlation option (R&S®FSMR3-B60), to measure the Phase Noise characteristics of a raw Signal Generator (R&®SMA100B).
31-Dec-2021 | AN-No. 1SL376
Fast Scalar Network Analysis Using a Signal Generator and a Power Meter
14-Jul-2006 | AN-No. 1MA101
A deep, segmented memory combined with dedicated trigger conditions solves this problem by permitting the acquisition of relevant sequences without long pauses.
01-Dec-2017
3GPP FDD and LTE Multicell and Multi-UE Scenarios with the R&S<sup>®</sup>SMU200A Signal Generator
10-Aug-2011 | AN-No. 1GP80
High-Speed Remote Control
12-May-2016 | AN-No. 1GP107
This application note shows how to perform LTE terminal block error rate (BLER) and throughput tests under fading conditions with the R&S®CMW500 Protocol Tester and the R&S®AMU200A Fading Simulator.
27-Mar-2012 | AN-No. 1MA177
Noise Figure Measurement without a Noise Source on a Vector Network Analyzer
27-Oct-2010 | AN-No. 1EZ61
The R&S®FSW signal and spectrum analyzer, the R&S®FSW-K160R and the R&S®FSW-K6 is ideal for testing modern radars.
04-Jul-2013
This application note describes how to use the LTE Frequency Division Duplex (FDD) and Time Division Duplex (TDD) measurement functionality provided by the R&S®CMW500 wideband radio communication tester to perform LTE transmitter and receiver measurements.
17-May-2013 | AN-No. 1CM94
Near Field Communication (NFC) Technology and Measurements
03-Jun-2013 | AN-No. 1MA182
This application note describes how all required transmitter (Tx) tests can be performed quickly and easily by using signal and spectrum analyzers.
11-May-2016 | AN-No. 1MA154
Combining the new R&S UPP audio analyzers with the R&S SMB100A signal generators provides the most compact and fastest test solution for modern FM car radios
19-Feb-2015
The antenna patterns of automotive radars provide a wealth of information that is of vital importance during radar development and validation.
28-Oct-2020
The R&S®FSW and R&S®SMW200A are leading hardware solutions for 5G NR base station tests - set up all required parameters in no time with just a few clicks.
25-May-2021
Cell search and cell selection in UMTS LTE
17-Sep-2009 | AN-No. 1MA150
This application note explains how to set up a vector signal generator for LTE FDD repeater conformance testing accordingg to various test cases defined in the 3GPP Technical Specification 36.143.
26-Apr-2013 | AN-No. 1GP85
Perform DPD on a vector signal generator for improved EVM performance
28-Aug-2023 | AN-No. 1GP139
The R&S FSWP phase noise analyzer is the perfect tool for verifying clock sources to ensure accuracy of design requirements and proper operation.
30-Sep-2021
Test your eCall and ERA-Glonass system modules - The R&S CMW500 and R&S SMBV100A are the ideal team for testing your eCall and ERA-Glonass cellular modems and GNSS receivers in the lab.
02-May-2022
This application note describes the differences in sweep speed between swept spectrum analyzers and modern spectrum analyzers with a wide-band FFT process, and how this improves the measurement speed for general spurious measurement.
10-Jul-2012 | AN-No. 1EF80
This application note gives the guidance of how to perform the BLE 5.1 DF RF tests according to the RF test specification of BT 5.1 by using the Rohde & Schwarz test solutions.
30-Oct-2019 | AN-No. GFM327
This application note explains how to detect, characterize, find and document interferers in cellular networks using the R&S®FSH spectrum analyzer.
21-Oct-2014 | AN-No. 1EF89
To ensure connectivity and trouble-free operation, each Bluetooth® enabled device has to be tested for conformance with Bluetooth SIG standards and regulatory requirements.
23-Nov-2017
Generating models with a VNA and using these on an oscilloscope via the deembedding
23-May-2023 | AN-No. 1SL393