Electronic Design - Media Center

video description

Multi-domain Debugging of embedded IoT Devices

Internet of Things (IoT) devices combine multiple functional cores in highly integrated wireless embedded designs and face often challenging long-term battery live time requirement. This video demonstrates on an example M2M IoT device the Multi-domain test capabilities of the R&S®RTO oscilloscope.

video description

MIPI D-PHY Compliance Test

This video shows the R&S®RTO-K26 MIPI D-PHY compliance test options which provides automated testing to the MIPI D-PHY standard for camera and display interfaces.

video description

Testing Conducted Emission in the R&D lab

Conducted emissions are electromagnetic disturbances caused by a device and conducted out by interconnects such as the power supply lines. Devices are required to pass stringent limits on the level of such emissions and these tests require expensive testing time at compliance laboratories. This video shows how the powerful spectrum analysis features in the R&S®RTO oscilloscope can be used to verify conducted emission levels relative to the requirements during development thereby ensuring passing results in the compliance laboratory.

video description

EMI Debugging

Meeting EMI and EMC requirements is critical to bringing electronic products to market. Compliance testing requires expensive equipment and test time at a compliance laboratory. Failures found late impact project costs and launch schedule due to debugging and re-testing. This video shows how the R&S®RTO oscilloscope can be used with a near field probe to find and fix EMI issues quickly and reliably during the development at the R&D lab thereby minimizing expensive re-testing and shortening time to market.

video description

eMMC Interfaces Compliance Test

Embedded multi-media cards (eMMC) are widely used in the industry as the primary memory for portable devices. The R&S®RTO-K92 eMMC Compliance Test option offers an automated test solution for the electrical interface of an eMMC device according to the JEDEC specification, revision 5.1.

video description

Measurement of very small currents

Measuring small currents has become increasingly important for battery powered portable and wearable consumer devices, IoT and medical applications. Designers of these devices must measure currents from the sub-milliampere up to the ampere range. The R&S®RTE and R&S®RTO oscilloscopes can measure currents down to 100 uA using their low noise and high-sensitivity current probe.

video description

Signal integrity of differential structures measured in the time domain

This video demonstrates how to efficiently and accurately measure signal integrity on differential transmission structures or balanced lines with the four-port R&S®ZNB vector network analyzer from Rohde & Schwarz. The R&S®ZNB in combination with the R&S®ZN-Z84 switch matrix enables straight-forward differential measurements in the time domain on multiple differential structures including rise time, differential impedance, intra-pair skew time and inter-pair skew time.

video description

How to set up eye diagram measurements with option R&S®ZNB-K20

The R&S®ZNB-K20 option enables to display eye diagrams on the R&S®ZNB and R&S®ZNBT vector network analyzers from Rohde & Schwarz. The video shows how to set up eye diagram measurements, how to perform mask tests with real life effects such as jitter and noise, and how to apply emphasis and equalization to improve the eye opening. The multiview display to analyze time domain, frequency domain and eye diagram in parallel and measurement data export for further analysis on an external computer are also addressed.

video description

Simplified eye diagram analysis with option R&S®ZNB-K20

The R&S®ZNB and R&S®ZNBT vector network analyzers from Rohde & Schwarz now support eye diagrams. Eye diagrams are used to determine the quality of a signal transmitting device. The video introduces the R&S®ZNB-K20 option which is fully integrated in the network analyzer firmware to allow easy access and operation. Simultaneous display of frequency domain, time domain and eye diagram analysis makes this solution ideal, for example, for compliance testing of digital interconnect technologies such as USB-C, Ethernet and PCIe.

video description

HMP Series - Programmable Power supply

  • HMP2020: 1 × 0 V to 32 V/0 A to 10 A; 1 × 0 V to 32 V/0 A to 5 A (188 W)
  • HMP2030: 3 × 0 V to 32 V/0 A to 5 A (188 W)
  • HMP4030: 3 × 0 V to 32 V/0 A to 10 A (384 W)
  • HMP4040: 4 × 0 V to 32 V/0 A to 10 A (384 W)

video description

HMO1002 Digital Oscilloscope

High sensitivity, multifunctionality and a great price – that is what makes the R&S®HMO1002 and R&S®HMO1202 digital oscilloscopes so special. From embedded developers to service technicians to educators – the wide range of functions address a broad group of users.

video description

HMC804x Power Supply

One, two or three channels – R&S®HMC804x power supplies with their specifications and wide range of functions are ideal for use in development labs and industrial environments.

video description

USB 2.0 Compliance Test Solution

The new R&S®RTO-K21 USB 2.0 Compliance Test software is an automated test solution according to the USB-IF test specification to address the testing of USB Device, Host and Hub applications at the various speed modes High-speed (USB specification 2.0: 480 Mbps), Full-speed (USB 1.1: 12 Mbps) and Low-speed (USB 1.0: 1.5 Mbps).

video description

Eye diagram measurement with the hardware clock data recovery of the R&S®RTO digital oscilloscope

Serial high-speed data interfaces such as USB 2.0, LVDS, HDMI or PCI-e require a special approach for jitter measurements as they use an embedded clock signal as time reference. Clock data recovery is required to extract the frequency and phase information of the embedded clock out of the data signal. The R&S®RTO digital oscilloscope with option R&S®RTO-K13 performs clock data recovery in hardware and real-time. This enables triggering on the embedded clock as well as fast histogram and eye mask testing on high-speed serial data signals with embedded clock.

video description

Jitter measurements with the jitter wizard of the R&S®RTO digital oscilloscope

Jitter measurements are required for characterization and debugging of fast clock and data signals. This is commonly referred to as "signal integrity" testing. Clock signals and data signals as part of parallel and serial interfaces are widespread in almost any electronic design. The jitter wizard of the R&S®RTO digital oscilloscope guides the user step-by-step through the configuration of the oscilloscope to perform common jitter measurements such as period and frequency, TIE, cycle-to-cycle jitter, and skew.

video description

Video testing on adaptive bitrate video streaming presented at GSMA MWC 2016

Rohde & Schwarz showcased full reference video testing based on the R&S®VTC/VTE/VTS video tester family at the GSMA Mobile World Congress 2016 in Barcelona. This video analysis solution is ideal for video quality testing with detailed video metric, independent from the type of the actual video service, on all kinds of terminal devices with an MHL, HDMI or Miracast video output.

video description

Video application testing and HDMI 2.0/MHL compliance certification presented at GSMA MWC 2014

Rohde & Schwarz presented the R&S®VTC/VTE/VTS video tester family at the GSMA Mobile World Congress 2014 in Barcelona. The video testers are used to test smartphone multimedia applications such as video-over-LTE transmission applications in order to ensure quality of service for end users and to test device interoperability with noncellular technologies such as Miracast, HDMI2.0 and MHL.

video description

R&S®BTC Trailer - A totally new dimension in compliance testing

This new all-in-one solution supports the generation and analysis of RF signals for all commonly used broadcast standards in one single instrument. The customized, cost-saving approach simplifies quality assurance in high-volume production.The advantages the new broadcast test center at a glance:

  • Modular, scalable platform
  • Maximum RF performance
  • Complete DUT test environment with signal generator, analyzer and simulator in one instrument
  • Automated tests that can be reproduced at any time

video description

Unrivalled phase noise measurement performance with the R&S®FSWP phase noise analyzer

The new R&S®FSWP phase noise and VCO tester from Rohde & Schwarz sets new standards in terms of sensitivity and measurement speed. Performing complex measurements at the push of a button, the R&S®FSWP is ideal for high performance radar and communication system applications. The phase noise tester can also be upgraded to a signal and spectrum analyzer.

Thank you.

Your request was successfully sent!

We will get in touch with you soon.

Your Rohde & Schwarz Team

Request Information
Topic: No Solution assigned to this page!

Please enter your inquiry.
Contact information

Please tell us how we can address you.

Please enter your first name.

Please enter a valid email address.

Please enter your company name.

Please enter your postal code.

Please enter your name.

Please enter your phone number.

Please enter your location.

Please enter your city name.

Please enter your street.

Please enter your number.

(e.g. 2nd floor, rear building)
Additional Information

Marketing permission
Security Response Code
show captcha

The input was not correct.
Do not enter data in this field
*Mandatory Field
Contact Us
International Website