R&S®FSVR - FAQ

Results 9
  • Different frequency data export using ASCII trace export SCPI commands

  • Sending a Remote Control Ccommand Internally

    I need to send a remote control command to the device, but I do not have a PC available to control the device.Can I do this internally with the device itself?Yes, Go to the device's Windows function Open the Windows Explorer Open the C:\Program Files\Rohde&Schwarz\Network Analyzer\Bin folder Execute the iecwin32.exe program Choose the RSIB interface and push the Connect Now button Now you can write

  • SCPI Command Tracking

    How do I perform SCPI command tracking?Using command tracking on the R&S FSL/FSV:- Turn on command tracking using the menu Setup/General Setup/GPIB/(FSL: More)/I/O Logging On- Start the remote program- After executing the remote program, you can browse through the log file located in the following folders:c:\R_S\Instr\scpilogging\ScpiLog.txtor for newer firmware versions:c:\Program Files\Rohde-Schwarz

  • How to automatically transfer IQ-data from FSVR Spectrum Analyzer to VSE software

    Name Last Modified SizeFSVR_IQ-data_transfer.py Mar 24, 2020 1 kB """ This simple Python example shows how to tranfer an IQ-data file from Spectrum Analyzer to the controller PC and open it with VSE signal analysis software. Tested with FSVR Real-Time Spectrum Analyzer. Updated on 24.03.2020 """ import pyvisa rm = pyvisa.ResourceManager() instr = rm.open_resource('TCPIP::192.168.0.1::INSTR') # replace

  • How to automatically transfer IQ-data from FSVR Spectrum Analyzer to VSE software - Python example

    Name Last Modified SizeFSVR_IQ-data_transfer_v1_3.pdf Feb 4, 2021 54 kB """ This Python example shows how to transfer an IQ-data file from Spectrum Analyzer to the controller PC and open it with VSE signal analysis software. Tested with: - FSVR Real-Time Spectrum Analyzer (FW: 2.23 SP1) - VSE Software (1.90) - PyVISA 1.11.3 - Python 3.9 Author: R&S Support - MP Updated on 22.01.2021 Version: v1.3 Technical

  • Dongle necessary for FS-K96?

    Is an FSPC license dongle (1310.0002.03) always needed to run the FS-K96 software?Yes, the FSPC is always needed for doing measurements. Without an FSPC and a license key, the FS-K96 software will operate in the demo mode - with no analyzer connection and access to only a few demonstration files.There are, however, two different versions of K96:FS-K96PC (1310.0219.06) can be run on a PC and used with

  • Measurement points of a spectrum analyzer

  • Self Alignment via remote control via TCP/IP => 'CAL?

    I want to make the Self Alignment via remote control with the command 'CAL?'.Because this takes sometimes a very long time how can I detect the end.In the manual is mentioned to use a SRQ, but this does not work when I use a TCP/IP connectionYes, the SRQ line is a hardware line with the IEEE bus and this does not work with normal TCP/IP. So we cannot use it.Because the calibration command is a query

  • Spectrum Analyzers - Export of trace data into a CSV file via remote control

    Name Last Modified SizeFPL_Measurement_to_CSV.zip Dec 10, 2020 77 kB

Thank you.

Your request was successfully sent!

We will get in touch with you soon.

Your Rohde & Schwarz Team

Download

Please enter your first name.

Please enter a valid email address.

Please enter your name.

Please enter your company name.

Please enter your location.

Marketing permission
Please enter the characters shown in the image
show captcha

The input was not correct.
International Website