Pesquisa de Artigos e Documentos

Describes all instrument functions and remote control commands, including measurement and programming examples.

English - 11 de set. de 2025

Provides the information required to prepare the instrument for use and start working.

English - 20 de out. de 2025

RSCommander is a versatile software tool for a wide range of Rohde & Schwarz spectrum-, network analyzers, signal generators and oscilloscopes. It allows for automatic instrument discovery, making screenshots, reading traces, file transfer and simple script creation.

English - 24 de dez. de 2017

Provides information on security issues when working with R&S®SMB100B in secure areas.

English - 4 de jun. de 2025

English - 21 de nov. de 2025

English - 5 de set. de 2024

Combining the R&S®UPP audio analyzers with the R&S®SMB100A signal generators provides the most compact and fastest test solution for modern FM car radios

English - 19 de fev. de 2015

Analog-to-digital converters (ADCs) have taken giant steps in speed and accuracy over the past years: Such devices allow high-speed video processing and even software defined radio (SDR) applications, where digitization is being performed at ever-higher intermediate frequencies (IF). This has clearly raised the bar for ADC test equipment, especially regarding the noise performance of the analog input signal and sample clock sources used in the test setup. The R&S®SMA100B offers outputs for the analog input signal of the ADC as well as the clock input signal in one single instrument - both with outstanding signal purity.

English - 11 de jan. de 2021

This Application Note describes characterization of devices used in radar systems with pulsed signals. The emphasis is on measurements using vector network analyzers (VNAs), signal generators, vector signal generators and spectrum analyzers.

English - 18 de jan. de 2008

The R&S®SMB100A analog signal generator is the ideal calibration source for weather radar receivers due to its highly accurate output level.

English - 25 de jan. de 2011

The Rohde & Schwarz Bluetooth RF test solution with the R&S®CMW and R&S®CMWrun is closely aligned to the Bluetooth RF Test Suite. Most of the tests can be performed with the equipment under test connected to a single CMW which is remotely controlled via R&S®CMWrun running on an external computer. Some of the tests require an additional signal generator. This document describes common setups for these tests and the required configurations.

English - 4 de mai. de 2015

This application note is a programming guide. It briefly summarizes basic tips and information about SCPI programming for remote-controlling Rohde & Schwarz signal generators.

English - 26 de abr. de 2013

For conducted immunity tests, EMC labs require a test signal source driven at high RF powers and at defined frequencies. Rohde&Schwarz offers a compact solution with a signal generator, an RF solid-state amplifier with power up to 350 W, power sensors and test software for the frequency range from 4 kHz to 400 MHz.

English - 3 de dez. de 2021

The R&S®SMB100A RF and microwave signal generator offers a remote emulation feature that makes it possible to control the instrument by commands other than the built-in native SCPI commands. This feature allows the user to replace signal generators, e.g. from other manufacturers, with the R&S®SMB100A without having to change the remote control code. This application note describes how to use the remote emulation feature in general. Furthermore, it describes in detail the remote emulation for each supported instrument, limitations of the individual emulations and the remaining differences between the emulated and the original commands.

English - 19 de mar. de 2012

Rohde & Schwarz signal generators can be connected in various ways to system controllers (typically PCs) and external PC peripherals. Although most of these connection operations are also explained in the instrument manuals, it is not always easy to maintain an overview. Operating manuals commonly focus on explaining a dedicated feature of a single instrument. This application note examines a range of typical user tasks and how to solve them with the different instruments.

English - 26 de abr. de 2013

After a communications satellite is on its target orbit, several routines need to be performed in order to ensure proper performance from the transponders in the payload. The on-orbit measurements are a vital part of the maintenance of a live satellite as well. Operating a satellite channel for an on-orbit measurement rather than the intended application comes with significant opportunity cost and hence test duration needs to be minimized as much as possible. Rohde & Schwarz test and measurement equipment recommended in this paper is market leading not only in terms of measurement accuracy but also offers unparalleled speed of measurement. This application note focuses on satellite post-launch or on-orbit measurement and monitoring strategies used for satellite functionality checks when running maintenance routines. A complementary paper treats pre-launch payload measurements.

English - 25 de nov. de 2016

The use of Rohde & Schwarz device drivers under VEE software is not complicated. However, a number of factors are involved, the errors that occur are often difficult to diagnose. This application provides easy and detailed support for installation and troubleshooting using National Instruments or Agilent GPIB boards.

English - 20 de dez. de 2012

This application note introduces the IVI High Speed LAN Instrument Protocol (HiSLIP) and outlines its features. HiSLIP is the successor to the VXI-11 LAN remote control protocol. This document also describes guidelines for using this protocol.

English - 12 de nov. de 2014

A Test Port Adapter System is implemented for all Rohde & Schwarz equipment, which operates above 26 GHz in order to protect the RF front-end from mechanical damage. The Test Port Adapter System consists of an RF front-end interface called the Test Port Adapter Body, and the Test Port Adapter Head which is attached to the Body. The Head provides an interface to a cable or device under test. This Application Note identifies the various types of Test Port Adapters, their parameters, compatibilities and usages.

English - 28 de abr. de 2015

Signal generators play a vital role in electrical test and measurement. They generate the test signals that are applied to components such as filters and amplifier, or even to entire modules, in order to ascertain and test their behavior and characteristics. The first part of this educational note presents the applications for and the most important types of signal generators. This is followed by a description of the construction and functioning of analog and vector signal generators. To permit a better understanding of the specifications found on data sheets, a closer look at the most important parameters for a signal generator is provided.Beyond the output of spectrally pure signals, a key function of RF signal generators is the generation of analog- and digitally modulated signals. The second part of this note therefore presents the fundamentals for the most significant analog and digital modulation methods.The third part of this educational note contains exercises on the topics of analog and digital modulation. All described measurements were performed using the R&S®SMBV100A vector signal generator and the R&S®FSV spectrum analyzer.

English - 3 de mai. de 2016

Signal generators are often used in automated test environment applications. The replacement of those instruments, e.g., due to malfunction or standard replacement procedures requires special care to be taken in consideration. Replacement of those instruments requires compabitiblity between the replacement and the replaced device in at least the electrical and remote-control features. This application note describes in detail how to use the emulation modes of the R&S® series SMA100A, SMB100A, SMF100A signal generators.

English - 24 de jun. de 2008

This Application Note describes a software program that provides easy creation and transfer of Pulse Trains between a PC and the R&S SMB100A, R&S SMA100A and R&S SMF100A analog signal generators with the Pulse Train option; or between a PC and the ARB of R&S SMBV100A, R&S SMJ100A or R&S SMU200A vector signal generators.

English - 10 de mai. de 2011

This document provides an introduction to SDR as used for military radios and presents the relevant T&M solutions offered by Rohde & Schwarz.

English - 14 de set. de 2012