Automotive ethernet and other bus systems

In-vehicle networks and ECU testing

Automotive Ethernet and other bus systems

Inside a typical car, you will find over 100 electronic control units (ECU) controlling everything from brakes, transmission, engine, A/C, steering, cameras, radar, acoustic sensors to the non-cellular and cellular wireless communications.

ECUs talk to each other via car buses, including controller area network (CAN), media oriented systems transport (MOST), local interconnect network (LIN) and FlexRay.

Automotive OEMs and Tier 1s are moving away from mixing so many different bus types to something more uniform, enabling higher data throughput, lower latency and less weight in order to reduce complexibility and increase cost-efficiency.

Features of Rohde & Schwarz automotive Ethernet testing solutions:

  • Trigger and decode capability for CAN, CAN-FD, LIN, FlexRay, CXPI, SENT, 100BASE-T1 and 1000BASE-T1
  • Compliance tests for automotive Ethernet (10BASE-T1S, 100BASE-T1, 1000BASE-T1, 2.5/5/10GBASE-T1 ) in accordance with standards such as 802.3cg, 802.3bw, 802.3bp, 802.3ch
  • Channel and Connector testing (100BASE-T1, 1000BASE-T1, 2.5/5/10GBASE-T1) according to OPEN Alliance TC9
  • EMI debugging, IVN signal & power integrity verification and analysis

Automotive Ethernet and other bus systems solutions

Automotive Ethernet compliance testing

More information

Automotive bus and protocol testing

More information

Domain controller and ECU development

More information

Battery Management System (BMS) testing

More information

Related resources for In-vehicle networks and ECU testing

Apllication card: Optimizing electric drivetrains with MXO oscilloscopes

Read this application card to learn about electric drivetrain improvements, different testing approaches, from high level three-phase harmonic improvements to gate driver switching analysis and test capabilities of MXO series oscilloscopes.

More information

Webinar: An introduction to 10BASE-T1S and its test challenges

This webinar analyses the 10BASE standard, identifies the associated test challenges and offers a robust test solution to ensure standards compliance.

More information

Webinar: Optimize electric drivetrain efficiency using power analyzers and oscilloscopes - Teaser

Webinar: Optimize electric drivetrain efficiency using power analyzers and oscilloscopes

Join our webinar to get an insight into characterizing electric drivetrain power efficiency, debugging losses and inefficiencies of components and the advantages of oscilloscopes and power analyzers.

More information

Poster: Electric drivetrain evolution – from past to future

Electric drivetrain developers must adopt new technologies such as fast-switching semiconductors and higher battery voltages to improve the efficiency and range of electric vehicles. Download this poster to get an overview of eDrivetrain developments and how to test them.

More information

Evolution of In-Vehicle Networks to Zonal Architecture - Teaser

Webinar: Evolution of In-Vehicle Networks to Zonal Architecture

Learn more about the evolution of In-Vehicle Network architecture, automotive Ethernet characteristics and compliance testing of Ethernet.

More information

1000BASE-T1 interoperability test

Application video: 1000BASE-T1 interoperability test

In this video we show how to perform the Signal Quality Indicator (SQI) test requirement for the OPEN Alliance TC12 Interoperability test with 1000BASE-T1.

More information

Webinar: How to ensure MultiGigabit automotive Ethernet compliance

Webinar: How to ensure MultiGigabit automotive Ethernet compliance

Join this webinar to learn about the newest updates to OPEN Alliance TC9 & TC15 and receive an in-depth analysis of different MultiGigabit test modes with solutions from Rohde & Schwarz.

More information

Poster: Evolution of in-vehicle networks

Developments in Advanced Driver-Assistance Systems (ADAS) are creating a new approach to In-Vehicle Network (IVN) architecture design. This poster graphically represents the development of IVNs over time and provides guidance on how to test them.

More information

Webinar: Domain controllers and CPUs

Webinar: Domain controllers and high performance CPUs for automotive

Testing and debugging Automotive domain controllers / high performance CPUs on their in-vehicle network interfaces, their performance and interoperability.

More information

Our experts

Ralf Oestreicher

Ralf Oestreicher

Modern vehicles typically have more than 100 electronic control units (ECUs), connected via various in-vehicle networks such as CAN, FlexRay, LIN, and Ethernet. These busses are used to exchange information and coordinate control. The higher volume of data generated by the rapid increase of sensors to support autonomous driving creates a demand for much higher data rate traffic within vehicles and today we have reached MultiGigabit Ethernet speeds. Of course, the data supports safety-critical functions so its integrity must be ensured. To verify the functionality of these data streams as well as the cables, domain controllers, ECUs and all parts of the in-vehicle networks, automotive engineers need to be able to search for specific signals, trigger, decode, measure crosstalk and perform standards compliance testing.

Flemming-Ernst-Rohde-Schwarz_6522_03.jpg

Dr. Ernst Flemming, Director of Product Management for oscilloscopes, Rohde & Schwarz

"Automotive Ethernet is now widely introduced in cars. In the OPEN Alliance, the industry has defined specific compliance tests. We offer a complete compliance test solution for 100BASE-T1 and 1000BASE-T1 that is widely accepted by OEMs, Tier 1s and test houses. With the new triggering and decoding solution for 100BASE-T1, automotive Ethernet can now be debugged the same way as the traditional CAN bus."

Sign up for our newsletter

Stay up to date with the latest news, information and resources

Sign up for our automotive newsletter