Centre de téléchargement

The efficiency of power transformers is a key factor in reducing energy losses within the power distribution network, not to mention the increasing regulatory pressure from energy-consuming facilities such as data centers. Inefficiencies in power transmission result in financial losses and elevated greenhouse gas emissions, both of which must be avoided. As part of type and acceptance testing, power transformers are both specified with respect to their essential electrical parameters and subsequently tested and certified for compliance with these and other regulatory requirements. High efficiency and full conformity are the ultimate objectives. To achieve this, all relevant electrical performance parameters must be measured and analyzed with the highest precision. In addition, manufacturers are increasingly required to perform special tests tailored to advanced and application-specific requirements.

English - 25 sept. 2026

This application note is about measurement accuracy of the LCR-Meters R&S®LCX100 and R&S®LCX200. On the R&S®LCX100 and R&S®LCX200, the accuracy is calculated in real time, depending on the instrument settings and on the measured impedance. It is displayed on the lower part of the instrument display. If no test instrument is available, or information about the measurement accuracy at a certain measured impedance is sought without having a DUT at hand, this accuracy calculation tool provides the desired values.The document explains the background of the calculation and the prerequisites for installing and running the program. The installer provided installs the program on your PC.

English - 11 mai 2023

This application note provides software and instructions for a simple check of the acoustic performance of mobile phones. It targets mainly service centers and repair workshops which have to perform incoming tests of defective mobile phones and final tests of repaired mobiles. A focus is set on short test times and ease of use, without compromising accuracy and repeatability of results.

English - 14 déc. 2017

This application note explains how to use the Audio Analyzer R&S UPV for measurements of maximum sound pressure level of headphones according to EN50332. It is possible to measure a combination of music player / FM receiver and headphones, the maximum output voltage of a player / FM receiver alone or the wideband characteristic voltage of headphones alone. An application program is available for download as installer file and as VB.NET project.

English - 16 juin 2009

This application note applies to DC power supplies R&S®NGL200, R&S®NGM200, R&S®NGP800, R&S®NGU201 and R&S®NGU401, as well as LCR meters R&S®LCX100 and R&S®LCX200. It provides an overview over ethernet-based remote services provided by the referenced R&S® instruments. These services comprise an instrument web page, VNC remote control and FTP file transfer between the instrument and a remote computer. The application note gives instructions on how to set up the instrument and the remote computer in order to be able to utilize these services.

English - 19 mai 2022

Precision loss power measurement of sheet iron and ferrite cores with high signal frequency: exact, easy and in real-time! With the ZES ZIMMER – A Rohde & Schwarz Company – precision power analyzer LMG611 and other LMG models it is possible to obtain the magnetic characteristics of transformer-cores and coil materials besides a precise measurement of power loss.Those could be the peak values of the magnetic flux, the magnetic field strength and the permeability of a core which are determined at low and at high frequencies. For the quality control of magnetic materials completely wound cores can be used.Many measuring proceedings require sinusoidal field strength or flux which require expensive and complicated signal sources. Since the main point of interest is especially the saturation interval, there will be a high demand for the source in this range. It is more elegant and cheaper to use "intelligent" measuring equipment and allow arbitrary curve forms of the voltage and the current and to apply some mathematics. In doing so low-cost power sources can be used. Even the line voltage with its high harmonic distortion can be used.

English - 25 sept. 2026

Describes all instrument functions and remote control commands, including measurement and programming examples, for the base unit.

English - 16 oct. 2026

Describes all instrument functions and remote control commands.

English - 10 juil. 2026

Describes all instrument functions and remote control commands, including measurement and programming examples, for the base unit.

English - 27 août 2019

Describes all instrument functions and remote control commands, including measurement and programming examples.

English - 11 sept. 2025

Describes all instrument functions and remote control commands, as well as measurement and programming examples.

English - 29 juil. 2026

Provides the information required to prepare the instrument for use and start working.

English - 26 juin 2024

Provides information on security issues when working with R&S®SMCV100B in secure areas.

English - 4 juin 2025

Describes all instrument functions and remote control commands, including measurement and programming examples.

English - 11 sept. 2025

Describes all instrument functions and remote control commands, including measurement and programming examples, for the base unit.

English - 13 août 2025

Provides the basic information required for remote control connections via SCPI.

English - 16 juil. 2025

Provides the information required to prepare the instrument for use and start working.

English - 29 juil. 2026

Describes the types of memory and their usage in the FSWX and issues when working in secured environments.

English - 4 déc. 2025

Describes all instrument functions and remote control commands, including measurement and programming examples.

English - 12 août 2025

Provides the information required to prepare the instrument for use and start working.

English - 15 oct. 2025

Describes all instrument functions and remote control commands, as well as measurement and programming examples.

English - 7 août 2020

Describes all instrument functions and remote control commands, including measurement and programming examples, for the base unit.

English - 22 août 2025

Describes the specific functions of the application, including the remote control commands with programming examples.

English - 2 oct. 2024

Describes all instrument functions and remote control commands, as well as application and programming examples.

English - 9 juil. 2026

Describes all instrument functions and remote control commands.

English - 10 juil. 2026

Describes the specific functions of the application, including the remote control commands with programming examples.

English - 2 oct. 2024

Describes all software functions and remote control commands, including measurement and programming examples, for the base software.

English - 26 juin 2026

Provides the information required to prepare the instrument for use and start working.

English - 22 sept. 2025

Describes the specific functions of the application, including the remote control commands with programming examples.

English - 2 oct. 2024

Describes all instrument functions and remote control commands, including measurement and programming examples.

English - 13 août 2025