Centre de téléchargement

RSCommander is a versatile software tool for a wide range of Rohde & Schwarz spectrum-, network analyzers, signal generators and oscilloscopes. It allows for automatic instrument discovery, making screenshots, reading traces, file transfer and simple script creation.

English - 24 déc. 2017

R&S®VISA is a standardized software library that allows fast communications over diverse interfaces with a wide variety of T&M instruments that are detected on the network from PC applications. R&S®VISA also includes a trace tool that simultaneously monitors communications between multiple applications and T&M instruments, and permits targeted analysis with the aid of efficient filters.

English - 26 mai 2020

Provides the information required to prepare the instrument for use and start working.

English - 16 déc. 2021

Rohde & Schwarz offers a powerful tool for remote control of their oscilloscopes - the RsInstrument Python module. This module enables users to control and automate their Rohde & Schwarz test & measurement instruments, including oscilloscopes, through Python scripts or interactive console communication.

English - 14 déc. 2023

Secondary surveillance radar (SSR) bridges the gap between communications systems and classic radar systems. Despite the increasing capabilities of mobile communications, SSR remains a major component in airspace surveillance. State-of-the-art methods such as Mode S reply enhance SSR with broadcast-like capabilities and enable airports in remote locations to surveil the airspace even if no radar is available. More advanced techniques such as automatic dependent surveillance broadcast (ADS-B) utilize the infrastructure provided by a Mode S reply transponder to provide even more information for ground control and other aircraft.

English - 17 mai 2021

Almost every switched-mode power supply (SMPS) needs an EMI (Electro Magnetic Interference) input filter to suppress any disturbances of the SMPS on the power lines. This requirement having an input filter in the design ensures that no negative effect will occur in other parts of the systems connected to the power lines. Therefore, the design and the validation of the input filter is a major task during a typical power supply design. The conducted emission (CE) test according to a specific standard is a suitable and a common validation method to release the design at the end of the development cycle. Nowadays, this conducted emission test will be performed as pre-compliance test during the development phase in the lab as well. In this case, the designer will obtain an early feedback whether the design has to be optimized regarding any disturbances present on the power lines. In most cases, the designer has to adjust the input filter to obtain a more effective suppression of disturbances generated by the SMPS. However, the designer needs to know details about the noise spectrum to optimize the input filter as effective as possible. In addition to magnitude and frequency information of the noise source, it would be very helpful to know whether the noise is generated by a common mode source or by a differential mode source. During the standard conducted emission test, common and differential mode noise is a combination in the measurement results and thus not possible to gain deeper insights. This document will describe a method to separate common-mode and differential-mode separation using two oscilloscope channels. This separation approach works without any additional hardware component like a noise separator. The designer will be able to distinguish between common-mode (CM) and differential-mode (DM) noise. This additional information about the dominant mode provides the capability to optimize input filters very efficiently.

English - 17 sept. 2020

French - 23 févr. 2026

The R&S®RTO / R&S®RTE oscilloscope is a valuable tool for analyzing EMI problems in electronic designs. High input sensitivity, high dynamic range and a powerful FFT implementation are key features for capturing and analyzing unwanted emissions.

English - 26 févr. 2015

A key challenge for embedded devices with DDR memories is to maintain signal integrity in the presence of power and ground rail fluctuations. This becomes even more important as supply voltages decrease and switching speed increases leading to tighter power rail tolerances and jitter requirements.

English - 5 avr. 2017

Power converter and inverter designs for higher power levels are usually based on hard switching half bridge configurations. In such setups, users must pay particular attention to proper switching operations to prevent shoot-through events. Setting up complex real-time trigger conditions using the R&S®RTE and R&S®RTO oscilloscopes increases the test coverage and robustness of converter and inverter systems.

English - 10 août 2020

Describes all instrument functions and remote control commands, as well as measurement and programming examples.

English - 27 janv. 2023

Modern, capacitive touchscreens as used, for example, in mobile phones are susceptible to common mode noise exhibited by external power supplies (EPS).

English - 17 mai 2018

Deep memory in an oscilloscope ensures that long waveforms are captured with high resolution right down to the details thanks to a high sustained sample rate. Users can be confident that they are not ‘missing anything’. They benefit from viewing longer periods of time and quickly finding signal anomalies or important events.

English - 21 mars 2017

This paper explains how to use the Rohde & Schwarz IVI.NET instrument drivers in Visual Studio environment from the prospective of an occasional C# programmer in need of automating a measurement task.

English - 31 mai 2016

Oscilloscopes are the workhorses for power electronics engineers. With powerful and easyto- use FFT analysis capabilities, their application fields extend to EMI debugging – and that saves a lot of time and money. A typical task is verifying the effectiveness of an EMI filter – early in the development phase.

English - 23 sept. 2019

Many serial interfaces use Manchester or non-return-to-zero (NRZ) coding. Oscilloscopes typically offer dedicated software options for debugging and testing the communications interfaces for common standards such as I2C, UART or CAN. The R&S®RTx-K50 option expands the addressable range of interface standards by adding decoding capability for standardized and proprietary Manchester or NRZ coded buses. It allows customizable configuration of the protocol structure that has to be decoded.

English - 19 oct. 2020

English - 17 nov. 2015

Rohde & Schwarz recognizes the potential risk of computer virus infection when con-necting Windows®-based test instrumenta-tion to other computers via local area net-works (LANs), or using removable storage devices.This white paper introduces measures to minimize malware threats and discusses ways to mitigate risks while insuring that instrument performance is not compro-mised.The paper discusses the use of anti-virus software. It also outlines how to keep the Windows® 7 operating system properly updated through regular installation of OS patches.

English - 27 janv. 2015

This application note describes the configuration of a Miracast wireless video transmission system and how to measure the delay times between a smart phone or tablet (source) and a television / monitor (sink) display. The accompanying software for Windows 7/8/10, Mac OS X 10.x and MATLAB additionally allows to measure the delay until the video signal is transmitted over the air and optionally until it is available on the HDMI cable of an external Miracast receiver.

English - 1 oct. 2015

Double-Pulse testing is a standard test-method used in power electronics design. Accurate measurements require a careful design of the test setup and the selection of the right measurement instruments. This application note discusses important aspects of double-pulse test setups as well as how to perform accurate measurements.

English - 22 mars 2021

French - 25 sept. 2024

With the R&S®RTO-K17/RTE-K17 High Definition Option the user will see more signal details with up to 16 bit vertical resolution.In combination with the superior analog front end of the R&S®RTO and R&S®RTE, the user has a versatile instrument in his hands to analyze a wide range of applications. From Switch Mode Power Supplies to Radar RF, the user can inspect all with one scope.

English - 13 avr. 2015

This Application Note gives 10 useful Tips & Tricks for the users of Rohde & Schwarz attribute-based instrument drivers. It is recommended for the first-time LabVIEW users as well as for the experienced programmers.

English - 30 janv. 2017

The power efficiency of the drive electronics is a key parameter when developing electric drive systems. The conduction loss of the electric drive electronics is of special interest. One important parameter for determining the conduction loss is the RDS(on) of the MOSFET. When a switching MOSFET is off, it has a high drain-to-source voltage, but when it is turned on, the voltage drops to just a few hundred millivolts. A highresolution oscilloscope is needed to measure these low voltages. Probe compensation and correct probing are also vital for accurate RDS(on) measurements.

English - 19 mars 2015