11 결과
Calibration and Verification Solution
The UWB (Ultra-Wideband) technology is a short range wide-band radio technology specified for device to device communication operating in unlicensed spectrum. It is an RF positioning technology that enables accurate and secure peer-to-peer ranging between mobile devices with robust resistance to interference while consuming very low energy and coexisting well with other radio communication systems. UWB is used for a variety of different applications, such as asset tracking, secure payment, personal tracker, real time location services and keyless access and start of a vehicle etc. According to ABI Research forecasts, there will be well over 1 billion UWB annual device shipments by 2026. Almost every smart phone shipped in 2026 will support UWB services.Talking about testing aspect of a UWB device, in general two test methodologies can be adopted as other wireless products, either the traditional testing mode (so-called conducted test mode) with wired RF connection between the test measurement equipment and device under test (DUT) or over the air (OTA) test mode in an OTA anechoic chamber. Sometimes, it is not always possible or necessary to perform the tests under conducted mode due to the limiting factors, e.g. cost, space, complexity and direct access to the RF connectors of the product. In this case, OTA testing is then becoming a non-evitable approach. Moreover, OTA testing reflects the usage of DUT in a real condition.In this application note, R&S® OTA test solution covering transmitter (Tx), receiver (Rx) and Time of Flight (ToF) testing in Wireless Automated Testing (WMT) environment is described. The measurement results throughout the whole document are based on NXP Trimension™ NCJ29D5 UWB automotive IC.
Apr 12, 2023 | AN-번호 1SL394
EDA 설계 시뮬레이션과 하드웨어 테스트를 연계하여 쉽고 직관적인 프로세스 흐름과 1차 제출 시 합격이 가능한 설계를 구현합니다.
8월 16, 2021
로데슈바르즈 신호 발생기는 규격에 부합하는 WLAN IEEE 802.11ax 신호를 생성하여 HE(High Efficiency) 수신기 테스트를 지원합니다.이 애플리케이션 노트는 적절한 신호 발생기 측정 솔루션을 선택하는 방법을 살펴보고 802.11ax SISO 및 MIMO 신호를 발생하는 방법을 단계별로 설명합니다. EVM과 같은 측정값을 사용하여 신호의 성능을 설명합니다. 그리고, 802.11ax 수신기 시험 규격을 설명하고 최근 소개된 IEEE P802.11ax/D1.3 규격 초안을 따르는 HE 트리거 기반 PPDU 규격에 대해 설명합니다.
8월 16, 2017 | AN-번호 1GP115
IoT(사물 인터넷)는 현재와 미래의 무선 통신을 주도하는 기술입니다. 3GPP는 Release 13에서 NB-IoT(Narrowband-IoT)를 새로운 물리 계층으로 지정했습니다. 이 애플리케이션 노트는 NB-IoT에 대해 간략히 소개하고 로데슈바르즈 솔루션을 이용한 간단한 측정을 보여줍니다.
6월 30, 2017 | AN-번호 1MA296
RFFE(Radio Frequency Front End)의 구성요소로 인한 왜곡은 통신 시스템의 성능과 처리량을 제한합니다. 왜곡의 유형은 다음과 같습니다.▪ AM-AM 및 AM-PM(진폭에 따른 게인의 복합 변동)▪ 비선형 주파수 응답(메모리 효과)모든 RFFE 구성요소에서는 이러한 왜곡이 모두 나타나며, 비율만 달라집니다. 이 애플리케이션 노트에서는 개별 RFFE 구성요소와 전체 RFFE의 계측에 대해 설명합니다. 그리고 선형화된 상업 SatCom BUC 제품의 이론적 한계와 비교한 내용을 포함하여 더욱 자세한 분석에 대해 알아봅니다.
2월 27, 2017 | AN-번호 1MA299
Tx FE(Transmit Frontend) 애플리케이션에서 최적의 Quasi-Linear Amplifier 아키텍처로 Doherty Amplifier가 출시되는 사례가 증가하고 있습니다.5G가 출시되고 Microwave 또는 밀리미터파 에어 인터페이스 탑재가 불가피해짐에 따라, 특히 증폭기와 결합기를 구성요소로 포함하는 사례가 증가할 것으로 예상되면서 구조와 관련된 설계 측면의 과제가 증가하고 있습니다.이 애플리케이션 노트는 Doherty Amplifier를 개선하여 성능 및 대역폭을 향상하는 측정 기반 개발 방법론에 대해 설명하며, 실제 예시 또한 포함되어 있습니다.이 방법론은 Balanced, Spatially combined Amplifier와 자체 중첩되는 경우가 많은 Anti-Phase Amplifier(Pushpull 혹은 차동 Amplifier로 불림)에 확대 적용할 수 있습니다.R&S®Quickstep 시퀀싱 소프트웨어는 다음 사이트에서 다운로드할 수 있습니다.
9월 26, 2016 | AN-번호 1MA279
점점 더 많은 모바일 무선 네트워크가 CPRI와 같이 표준화된 전송 프로토콜을 사용하는 디지털 인터페이스를 통해 기지국 본체로 연결하는 원격 RE(Radio Equipment)를 구현하고 있습니다. 로데슈바르즈는 RE 기기 테스트를 지원하는 R&S®EX-IQ-BOX [모델 K04] 기반의 완전한 테스트 솔루션을 제공합니다. 이 핵심 구성 요소는 CPRI 데이터 전송을 사용하여 로데슈바르즈 테스트 장비를 테스트 RE에 연결하는 데 사용하는 디지털 인터페이스 모듈로 사용자 구성이 가능합니다. 이 애플리케이션 노트는 원격 라디오 헤드를 성공적으로 테스트하는 데 필요한 기기 설정 및 구성에 대해 자세히 설명합니다.
8월 05, 2013 | AN-번호 1GP78
This application note helps the user to configure a Rohde & Schwarz vector signal generator for LTE FDD repeater conformance testing. It explains step by step how to set up the baseband signal for the various test cases defined in the 3GPP Technical Specification 36.143.The R&S®SMx vector signal generators provide predefined, LTE-conform test models and are therefore ideal for LTE repeater conformance testing. The test cases in TS 36.143 can be set up with a single instrument which provides all necessary test signals including the four specified repeater stimulus signals.
Apr 26, 2013 | AN-번호 1GP85
로데슈바르즈 신호 발생기는 뛰어난 EVM 성능으로 최대 160MHz 대역폭의 표준 적합 WLAN IEEE 802.11ac 신호를 생성할 수 있습니다. 이 애플리케이션 노트는 신호 발생기 테스트 솔루션과 테스트 신호를 구성하는 방법을 단계별로 설명합니다. EVM 성능을 설명하기 위한 몇 가지 측정들이 설명됩니다.
4월 26, 2013 | AN-번호 1GP94
이 애플리케이션 노트는 R&S® 테스트 및 계측 제품을 GPIB 또는 LAN 인터페이스를 통해 AWR® Visual System Simulator™(VSS)에 빠르고 원활하게 연결하는 방법에 대해 설명합니다. 로데슈바르즈 하드웨어에 맞춰진 AWR® Connected™와 R&S® WinIQSIM2™ Signal Simulation 소프트웨어를 사용하여 디지털 무선 표준들의 유연성에 대해 자세히 알아보고 VSS에 통합하는 방법을 설명합니다.
5월 20, 2010 | AN-번호 1MA174