82 Results
I want to set the trigger source of my FSMR to AM. But it always sets the trigger source to RF level. How can I set the trigger source to AM ?
Can I use my own antenna/probe set with EMC PreCom
How can I set up the RTH for correct RS232 / UART decoding?
All four S-parameter remote set up
How to set the preselector to off
How to set a static TCP/IP address
How can I set up the RTH for correct CAN decoding?
LTE UE capabilities Interpretation of Bandwidth Combination Set values shown in CMW Callbox
With the NRX how can I set a measurement result directly as a reference value for relative measurement via remote control?
Remote Control: How to read out the Frequencies of a Transducer Set.
How can I set the special slot format in 5G NR measurement application for TDD?
How can I set the TCP/IP settings from DHCP to Static?
Convert the trace data in a dataset file (*.SET) to a CSV file
FAQ; Why do I see only one Result Table in the EMC32 Explorer although I set two Detectors?
I want to use Port 1 and Port 3, so I tried to switch them on by setting the value to 1 (the default value) and to switch off Port 2 and Port 4 by setting the value to 0. But this does not work. How do I set the ports?
I would like to do a Reference Calibration using ELEKTRA and Field Probe. For this I have to do Reference Calibrations at 16 positions, this does mean my Field Probe have to be set to each of the 16 predefined points. I set the probe positions manually, so an error can occur by mistake. Is it possible to repeat a measurement for a sensor position, if needed?
Kindly help me to run the software.After installation, I am getting error message to run the software.
What can I do to set up a valid transducer?
I want to set the acquisition mode to Average + HR using SCPI commands. But I can not find the right command in the manual.
How can I set up EMC32 so that it is possible to measure with the forward and reverse power with NAP?
When I set the frequency of the arbitrary generator to 10 KHz, the frequency of the output signal is 120 KHz. What is wrong here?
I am using the burst function of the function generator. But I can not find the remote command to set the burst to "manual".
When yout set the carrier frequency and the filter bandwidth, you get the warning "CF + BW/2 > DevBW".
I have set my VNA to single sweep mode and switched on averaging with a factor of 10. But when I restart the single sweep, it stops after 1 sweep and the averaging is not done.
Is it possible to set up an IP peer to peer test using CMW500 between a corporate network and one EUT attached to an LTE cell?
In the manual of your oscilloscopes you state: If AC coupling is set, the attenuation of passive probes has no effect, and voltage is applied to the instrument with factor 1:1
We have installed our test system with EMC32 and all devices, but NRP2 can not be set to physical from EMC32 using LAN interface.
I tried to change the working directory on my FPC series analyzer without success. It stays to "\Public" all the time. Can you explain how to set the desired directory?
I want to use the LCX series LCR Meter to automatically control and sort components. One of the tasks is to differentiate between the following three values of resistors: - Less than 990 Ohm, - Middle range from 990 to 1010 Ohm (1 kOhm), - More than 1010 Ohm. How can I set this measurement up and which pins do I have to use at the 15 PIN SUB-D socket at the rear side of the LCX?
A sinus signal with i.e. 10 V peak-peak, frequency 1 MHz is applied. If I choose a vertical scale which is too small the peaks of the waveform are not displayed as they are out of range. Now I activate the digital filter in the “Vertical” menu à “Channel”. The frequency of the filter is also set to 1 MHz. Now even at very small vertical scales (i.e. 50 mV/div) the waveform is displayed completely, see screenshot. But the amplitude can not be correct. What goes wrong here?