R&S®TS-PIO5 Digital LVDS Functional Test Module

PCI/PXI module for R&S®CompactTSVP test system

  • Übersicht

Key Facts

  • Two MDR connectors with 10 LVDS channels each (8 × data, 1 × general purpose, 1 × clock); bidirectional LVDM with fixed termination (100 Ω)
  • Two single ended control lines per connector

Brief Description

The R&S®TS-PIO5 digital functional test module is a compact PCI/PXI module which takes up only one slot in the R&S®CompactTSVP test system versatile platform.

Specifications

Application in R&S®CompactTSVP platform
R&S®CompactTSVP 1 slot required
Interfaces
Control bus CompactPCI/PXI

Key Facts

  • Two MDR connectors with 10 LVDS channels each (8 × data, 1 × general purpose, 1 × clock); bidirectional LVDM with fixed termination (100 Ω)
  • Two single ended control lines per connector
  • +5 V/max. 0.30 A power supply available at each digital connector, protected by diode and fuse
  • 10 channels RS-485 (RS-422) compatible I/O channels with interface connector onboard
  • Pattern rate up to 200 Mbit, 5 ns resolution
  • Stimulation of digital realtime data streams with 2 M pattern memory onboard
  • Acquisition of digital realtime data streams
  • LVDS transceivers with internal ESD protection
  • FPGA-based flexibility and simultaneous task operation independent of the operating system
  • Triggering (bidirectional) via PXI trigger bus; resolution based on PXI or external clock, ≥ 10 ns
  • Synchronization via
    • TTL external clock input (SMB plug)
    • LVDS clock lines (MDR connector)
    • PXI clock 10 MHz
  • Jitter and signal delay compensation in steps of typ. 2.5 ns, 180 ° phase shift or delay of numerous clock cycles (combination possible)
  • Self-test software
  • Software front panels for immediate use
  • LabWindows/CVI device driver support
  • Test software library GTSL in DLL format

Brief Description

The R&S®TS-PIO5 digital functional test module is a compact PCI/PXI module which takes up only one slot in the R&S®CompactTSVP test system versatile platform.

The R&S®TS-PIO5 digital functional test module contains very flexibly programmable bidirectional LVDS channels to acquire and stimulate static or dynamic digital patterns. The channels are permanently terminated on board as the LVDM driver tolerates the resulting impedance of 100 Ω in driver mode. Synchronization to digital communications, handshake signals and analog measurement tasks are provided via trigger lines accessible at the front connector or via the PXI trigger lines. The module also generates trigger pulses derived from digital pattern comparisons and performs change detection at the input ports to interact with other slot cards inside the R&S®CompactTSVP chassis.

Specifications

Application in R&S®CompactTSVP platform
R&S®CompactTSVP 1 slot required
Interfaces
Control bus CompactPCI/PXI
DUT connector (front) 2 × Mini D Ribbon (MDR) connectors
2 × SMB plug connectors
Rear I/O connector CompactPCI connector, 110 pins
Side connectorRS-485Semtec terminal strips (2.54 mm)
Module features
Front connectors
DIGITAL A/B2 × Mini D Ribbon (MDR) connectors2 × 8 LVDM data I/O channels
2 × 1 LVDM general purpose I/O channels
2 × 1 LVDM clock I/O channel
2 × 2 LVTTL digital I/O channels
CLK, TRIG2 × SMB connectors1 clock I/O channel, 1 trigger I/O channel
LVDS channels (data input mode)
DIGITAL A/B 2 × MDR connectors
Input modeshalf-duplex operationLVDM with termination 100 Ω
Difference input voltage max. ±600 mV
Difference input threshold min. ±100 mV
Input resistance 100 Ω
Realtime acquisitionsample rate (SDR)0.01 bit/s to 100 Mbit/s (10 ns resolution)
 sample rate (DDR)200 Mbit/s (only for data channels)
LVDS channels (data output mode)
DIGITAL A/B 2 × MDR connectors
Output modeshalf-duplex operationLVDM with termination 100 Ω
Output voltage|VOD|, into 50 Ω load (double termination)247 mV (min.), 454 mV (max.)
Output currentIOSmax. 10 mA
Tristate control programmable per channel and up to 50 Mbit/s per sample
Realtime stimulationsample rate (SDR)0.01 bit/s to 100 Mbit/s (10 ns resolution)
 sample rate (DDR)200 Mbit/s (only for data channels)
TTL channels (input/output mode)
DIGITAL A/B 2 × MDR connectors
Input/output modevoltage3.3 V logic; 10 kΩ pullup onboard
Realtime stimulation/acquisitionsample rate0.01 bit/s to 50 Mbit/s (10 ns resolution)
Connectoronboard connectorpin connector (terminal strips 2.54 mm)
Input/output mode RS-485/422 signal level, 10 bidirectional channels, no RS-485 serial protocol
Realtime stimulation/acquisitionsample rate0.01 bit/s to 20 Mbit/s with 10 ns resolution
Realtime stimulation/acquisition memorydata buffer depth/width (programmable)2 M pattern at 32 bits (18 × LVDS, 4 × TTL, 10 × RS-485)
External clock
DIGITAL A/Binput/output voltageaccording to LVDS channels, 2 × MDR connectors
 frequency range20 MHz to 50 MHz
CLKinput/output voltage3.3 V TTL logic (SMB plug)
 frequency range20 MHz to 50 MHz
Trigger
TRIGinput/output voltage3.3 V TTL logic (SMB plug)
PXIinput/output voltage8 x PXI, 5 V TTL logic
Synchronization
Trigger unitsapplications2 x fully independent hardware trigger logic
❙ programmable trigger generator
❙ generation of realtime stimulation clock
❙ generation of realtime acquisition clock
❙ frequency measurement
Trigger unit characteristicsreference pattern10-bit, 3 states: high, low, don’t care
 slopepositive/negative
 trigger delay setting0 s to 100 s (10 ns resolution)
 output signals❙ trigger received signal (pulse)
❙ trigger active signal (start of trigger until burst end)
❙ sample pulse (pulse for each sample)
Synchronization inputschannels1 × TTL trigger (TRIG)
8 × PXI trigger bus
1 × pattern comparator
Synchronization outputschannels1 × TTL trigger (TRIG)
8 × PXI trigger bus
 signals❙ output, trigger unit 1 (IT1)
❙ output, trigger unit 2 (IT2)
❙ TTL signal (TRIG)
General data
Environmental conditions
Power consumption 5 V: typ. 1 A, 3.3 V: typ. 1 A
Temperatureoperating temperature range+5 °C to +40 °C
 storage temperature range–10 °C to +60 °C
Damp heat +40 °C, 80 % rel. humidity,
steady state, in line with
EN 60068-2-30
Mechanical resistance
Vibrationsinusoidal5 Hz to 55 Hz, 0.15 mm amplitude const.,
55 Hz to 150 Hz, 0.5 g const.,
in line with EN 60068-2-6
 random10 Hz to 300 Hz, acceleration 1.2 g (RMS),
in line with EN 60068-2-64
Shock 40 g shock spectrum,
in line with MIL-STD-810E, method 516.4, procedure I
Product conformity
Electromagnetic compatibilityEU: in line with
EMC Directive 2014/30/EC
applied harmonized standards:
EN 61326-1: 2013 (industrial environment),
EN 61326-2-1: 2013,
EN 55011: 2009 + A1: 2010 Group 1, Class A
Electrical safetyEU: in line with
Low Voltage Directive 2014/35/EC
applied harmonized standard:
EN 610110-1: 2010
DimensionsW × H × D316 mm × 174 mm × 20 mm
(12.4 in × 6.8 in × 0.8 in)
Weight 0.21 kg (0.47 lb)
International Website