Search Application Notes & Cards
Learn how to configure Rohde & Schwarz products to fit your application. Search our database by product, technology, or application to find relevant technical documents.
Search Application Notes & Cards
Learn how to configure Rohde & Schwarz products to fit your application. Search our database by product, technology, or application to find relevant technical documents.
42 Results
The R&S®CMW wideband radio communication tester platform (R&S®CMW500, R&S®CMW270) uses high accuracy distance measurements (HADM) with phase based ranging (PBR) for a comprehensive and fully automated test solution to verify Bluetooth® Low Energy physical layer functionality
06-Sep-2023
The R&S®CMW500 and R&S®SMBV100B are the ideal team for motor vehicle type approval testing of your eCall and ERA-GLONASS cellular modems and their GNSS receivers in line with the EU2017/79 regulation.
02-May-2022
Automating measurement setups is advantageous for multiple reasons. It saves time in case of repeated measurements and in hazardous environments, instruments can be operated from a distance. The measurements are repeatable because they are always performed with a defined procedure, leading to higher test confidence.But in remote control applications, users often perceive synchronization and binary transfers as challenging. Therefore, this application note focuses on binary transfer of data to and from the instrument and shows code example to demonstrate the ease of use.
31-Mar-2022 | AN-No. 1SL381
RF system noise contributions define receiver capabilities and sensitivity. The noise figure measures how the critical components affect the signal.
28-Jan-2022
R&S®Server-Based Testing helps reduce test times for workloads that can be parallelized. 5G New Radio (5G NR) multicarrier signals are an ideal workload because each component carrier can be analyzed independently and in parallel. In an example EVM measurement, scenario test times are reduced significantly even when receiving I/Q data from just a single instrument.
13-Sep-2021
The verification of emissions according to EN or FCC standards is mandatory to avoid any interference with existing users. Besides the common emission tests with measurement bandwidth up to 1 MHz and mean power measurements, most regulations also require to test peak transmission power within a 50 MHz bandwidth to avoid interference with any existing wideband applications, for example radar receivers. This application note provides information how to perform spectral emission measurements on UWB signals with spectrum analyzers using wide bandwidth RBW filters, and explains the capabilities and the limiting factors of the Rohde & Schwarz FSW signal and spectrum analyzer to perform this measurement. The next sections will give further details.
28-Jun-2021 | AN-No. 1EF109
Primer
A power sensor is a fundamental measurement tool in RF engineering. However, today's marketplace is filled with myriad choices, and many are making bold claims about attributes such as measurement speed and readings per second. As a result, it can be difficult to cut through the hyperbole and determine which sensor will actually meet the requirements of a specific measurement.This primer outlines the basics of RF power sensors and highlights a few key characteristics that will help you select the best one for each application. The narrative has three parts. First, we focus on choosing the right type of sensor: multipath, wideband, average power and thermal can satisfy slightly different measurement needs. The second section covers the five major attributes of sensor performance, and what to look for relative to your requirements. Finally, we outline three ways to integrate a sensor into your measurement application.
26-May-2021
The UWB (Ultra-Wide Band) technology is a low power wide-band technology specified for device to device communication.It is an optimal RF positioning technology that enables accurate and secure peerto-peer distance measurement between mobile devices with robust resistance to interference while consuming very low energy and coexisting well with other radio communication systems.This application note describes how to use the UWB measurement functionality provided by R&S®CMP200 radio communication tester to perform HRP UWB PHY measurements for R&D and production purposes.
19-May-2021 | AN-No. GFM362
Phase difference is the key parameter when characterizing direction finding (DF) scenarios. To analyze DF equipment, the phase difference needs to be determined before measuring other parameters such as the bearing. The R&S®VSE-K6A multichannel pulse analysis software in combination with a Rohde & Schwarz oscilloscope provides phase difference measurements even in challenging environments, utilizing the test equipment’s advanced trigger capabilities.
02-Mar-2021
conducted conformance testing according to TS 38.141-1, Rel. 16
3GPP defines the Radio Frequency (RF) conformance test methods and requirements for 5G NR Base Stations (BS) in the technical specifications TS 38.141. This application note describes how all mandatory RF transmitter tests (TS 38.141-1, chapter 6), according to Release 16, can be performed quickly and conveniently with signal or spectrum analyzers from Rohde & Schwarz by either choosing manual operation or a remote control approach. Moreover, some test cases require additional signal generation equipment from Rohde & Schwarz.In Addition, a new Python software library comes with this application note to enable the remote control approach of base station testing. This example requires the RsInstrument module which can be found on pypi.org or installed via 'pip' and is provided as is.
27-Jan-2021 | AN-No. GFM313
conducted conformance testing according to TS 38.141-1, Rel. 15
3GPP defines the Radio Frequency (RF) conformance test methods and requirements for 5G NR Base Stations (BS) in the technical specifications TS 38.141. This application note describes how all mandatory RF receiver tests (TS 38.141-1, chapter 7), according to Release 15, can be performed quickly and conveniently with signal generators from Rohde & Schwarz by either choosing manual operation or a remote control approach. Moreover, one test case requires a signal or spectrum analyzer from Rohde & Schwarz which is highlighted seperately in the corresponding chapter.In Addition, a new Python software library comes with this application note to enable the remote control approach of base station testing. This example requires the RsInstrument module which can be found on pypi.org or installed via 'pip' and is provided as is.
02-Dec-2020 | AN-No. GFM314
Verify and optimize your product design under realistic fading conditions in a deterministic lab environment that allows repeatable measurements using standardized and user-defined fading profiles.
27-Oct-2020
Timing components such as low jitter oscillators and clocks are necessary to facilitate increasing data rates in high speed digital designs. As part of the overall system design, the components also have to perform in the system’s non-ideal power integrity environment and limit the power supply induced phase noise and jitter from power rail disturbances. Measuring the power supply noise rejection (PSNR) requires accurate generation and leveling of artificial, sinusoidal disturbances and measurement of resulting phase-noise and jitter impairments.
30-Sep-2020
radiated conformance testing according to TS 38.141-2, Rel. 16
3GPP defines the Radio Frequency (RF) conformance test methods and requirements for 5G NR Base Stations (BS) in the technical specifications TS 38.141. This application note describes all mandatory RF receiver tests (TS 38.141-2, chapter 7), according to Release 16.Furthermore, this document provides a brief introduction about the different R&S OTA antenna test solutions and how they are applicable for base station conformance testing. Rohde & Schwarz offers suitable solutions for any test case that is mentioned in this application note.
30-Jun-2020 | AN-No. GFM325
The R&S®FSW offers a variety of different bandwidth options and makes it possible to combine these with external harmonic mixers to enlarge the analyzer’s frequency range up to 325 GHz. This application card will give some guidance as to the possible combinations of bandwidth options and mixers in conjunction with the needed IF frequencies.
16-Jun-2020
The required bandwidth span for power amplifiers is growing, driven by the latest 5G and satellite enhancements.Ideally, amplifiers support multiple bands. This makes wideband testing more essential than ever before.
19-May-2020
Signal Generation and Analysis
This Application Note supplements the video series, describing signal generation and signal analysis for Dynamic Spectrum Sharing (DSS) for LTE and 5G NR. The video series is located below this paragraph.In this illustration, a four frame (40 subframes) long LTE sequence will be created, and exemplary MBSFN slots inserted, carrying 5G payloads. That signal sequence will be compiled and played by the SMW signal generator. The FSW signal analyzer LTE and 5G NR personalities are then used to analyze and verify the content of each subframe/slot.Three methods are presented, (1) Manual Entry using the GUI, (2) SCPI command sequence/remote control and (3) configuration file. The latter variants require the download of various files, available at the bottom.The configuration file approach offers the fastest time to initially setup. The SCPI command sequences provides some insight of the functionality and settings at each step, and the supplied MATLAB® script (only core license required) provides a prototype to illustrate the programming of successive slots or subframes. The Manual Entry approach, using the instrument's front panel GUI, provides a step-by-step set-up instruction, which can itself be augmented with SCPI recording, for easy modification and programming.MATLAB® is a registered trademark of The Mathworks, Inc.
30-Mar-2020 | AN-No. GFM337
An easy-to-setup test solution for high speed multichannel acquisition for 5G NR signals
04-Mar-2020
With the start and spread of 5G communications services and new form factors such as wearables and foldable phones, an increasing number of flexible printed circuit boards (PCB) that support high frequency signals are being produced. These boards must exhibit excellent frequency characteristics. In the past, a PCB’s frequency characteristics were subjected to sampling inspection using a test coupon. For flexible PCBs, a new method is needed to provide repeatable and proper verification. The Yamaha® MP Series combined with the R&S®ZNBT vector network analyzer measure the high frequency characteristics of a production lot at high speed and high accuracy, enabling 100 % measurement of mass produced rigid and flexible PCBs.
27-Jan-2020
radiated conformance testing according to TS 38.141-2, Rel. 16
3GPP defines the Radio Frequency (RF) conformance test methods and requirements for 5G NR Base Stations (BS) in the technical specifications TS 38.141. This application note describes all mandatory radiated RF transmitter tests (TS 38.141-2, chapter 6), according to Release 16.Furthermore, this document provides a brief introduction about the different R&S OTA antenna test solutions and how they are applicable for base station conformance testing. Rohde & Schwarz offers solutions for any test case that is mentioned in this application note.
20-Dec-2019 | AN-No. GFM324
Create and simulate detailed traffic situations for the verification of cellular V2X (C-V2X) connectivity.
18-Nov-2019
This application program supports the logging and fast logging functionality of the power supplies R&S® NGM200, NGU201 and NGU401. Standard logging is also supported with power supply R&S® NGL200 and NGP800. Power supplies R&S® NGA100 and NGE100 are supported in the data collection mode. Charting functionality is available for logged voltage, current and power values.
14-Nov-2019 | AN-No. 1GP122
Blocking test, WLAN, Wi-Fi, RF device, performance limit Customize blocking tests and make sure to address parameters like frequency positions, levels or bandwidths when verifying RF device performance. Verifying RF device performance with a blocking test Blocking test, WLAN, Wi-Fi, RF device, performance limit Customize blocking tests and make sure to address parameters like frequency positions, levels
31-Oct-2019
conducted conformance testing according to TS 38.141-1, Rel. 16
3GPP defines the Radio Frequency (RF) conformance test methods and requirements for 5G NR Base Stations (BS) in the technical specifications TS 38.141. This application note describes how all mandatory RF performance tests (TS 38.141-1, chapter 8), according to Release 16, can be performed quickly and conveniently with signal generators from Rohde & Schwarz by either choosing manual operation or a remote control approach.In Addition, a new Python software library comes with this application note to enable the remote control approach of base station testing. This example requires the RsInstrument module which can be found on pypi.org or installed via 'pip' and is provided as is.
24-Oct-2019 | AN-No. GFM315
Next Generation Emergency Call (NG eCall) is a extension of eCall, a service provided in Europe with the goal of reducing response times for accidents or other emergencies on the roadways. This application note briefly describes the technology behind NG eCall and presents conformance tests for NG eCall using the R&S®CMW500 RF tester and either the R&S®SMBV100B or the R&S®SMW200A vector signal generator. The test software for NG eCall (R&S®CMW-KA096) makes it quick and easy to perform these tests with the LTE wireless communications standard.
06-Jun-2019 | AN-No. GFM312
The document gives an overview and user guide about a link budget calculator for the main components of a basic OTA system. The calculator shall guide the user to plan link budgets, especially with respect to SNR requirements for the receive components and the vector signal analyzer. An Excel sheet containing the Link Budget Calculator accompanies the application note.
19-Mar-2019 | AN-No. 1EF104
This application note describes Battery Life Measurements with the R&S®RT-ZVC02/04 Multi-Channel Probe. The measurements are described with the use of an oscilloscope. The R&S®RT-ZVC Multi-Channel Probe can be used with R&S®RTE1000, R&S®RTO2000 or R&S®RTP.
17-Jan-2019 | AN-No. 1TD07
30 dBm + 30 dBm = 60 dBm? It is well known that it is not as easy as that.
This application note supplies a free of charge software tool that can be used to add or subtract an arbitrary number of powers. In addition, the software can be used to convert power and voltage units from the linear to the logarithmic scale (and vice versa), convert linear power and voltage ratios to decibels, and convert a VSWR to other reflection quantities.
10-Dec-2018 | AN-No. 1GP77
An ever-increasing requirement for data on mobile networks, driven by a myriad of applications from HD video on the move to autonomous vehicles and Industrial IOT, means a part of the new 5G network is to be deployed at mmWave frequencies, with a 26 GHz pioneer band defined for the UK between 24.25 - 27.5 GHz.This near 10-fold increase in frequency over 4G networks opens several challenges, both in the design and implementation of the required sub-components, network infrastructure and end user equipment, and in parallel in the test and measurement approaches used to drive these developments.In this presentation, we will introduce some of the main challenges in test and measurement of a device at these frequencies. We will then present the testing of a 26-28GHz pioneer band dual channel amplifier evaluation module using 5G NR test waveforms.
26-Nov-2018