R&S®MXO Series family, R&S®RTP and R&S®RTO6 oscilloscopes support decoding and triggering of aerospace protocols such as MIL-STD-1553, ARINC 429, SpaceWire. Find out more about the software package here.

Low speed serial buses such as I2C/SPI, RS-232/UART and Manchester/NRZ on your Rohde & Schwarz instrument. Your oscilloscope can provide a system-level view of one or more serial buses that is time correlated with other system events

Rohde & Schwarz current probes allow you to accurately and non-intrusively measure AC and DC currents. Different probes from 20 kHz to 120 MHz are available. Learn more.

The R&S®WPU2000 wideband processing unit provides wideband radar analysis with up to 2 GHz real-time bandwidth for the frequency range from 8 kHz to 40 GHz.

The R&S modular probe system addresses current probing requirements with a technically sophisticated, yet easy-to-handle solution. Explore now!

The FSWX is the first signal and spectrum analyzer with multichannel spectrum analysis, cross-correlation (x-correlation) and I/Q preselection.

The R&S®SMCV100B vector signal generator is used for generating wireless, cellular, broadcast, navigation or customer specific RF signals in the frequency range from 4 kHz up to 7.125 GHz.

R&S® ROMES4 drive test software is ideal for optimizing all technologies from a single source. Find out more.

Active omnidirectional antenna – for active omnidirectional reception of horizontally polarized waves in the frequency range from 20 MHz to 500 MHz.

Active vertical dipole – monitoring antenna for vertical polarization in the frequency range from 20 MHz to 1.3 GHz for stationary and mobile use

ARDRONIS GNSS - disruption of autonomous drones that use GNSS based localization

Active rod antenna – monitoring antenna for vertically polarized signals in the frequency range from 8.3 kHz to 100 MHz for stationary and mobile use.

With measurement bandwidths of up to 500 MHz and very high sensitivity, the R&S®FSWT fulfills the requirements for a TEMPEST measuring receiver.

The R&S®RTP-K114 and R&S®RTP-K115 options enable DP 1.4b and eDP 1.4a/1.5 compliance testing on R&S®RTP oscilloscopes.

The R&S®MIPI C-PHY compliance test options offer an automated test solution according to MIPI and UNH-IOL test specifications. Learn more here.

R&S®RTP and R&S®RTO oscilloscopes support TX and RX compliance tests for V1.1/2.0/3.2 Gen 1&2

The option R&S RTP-K110 enables HDMI 1.4b/2.1 compliance testing on the R&S RTP oscilloscopes.

The realtime deembedding of signal path characteristics is based on S-parameters. Learn more about the deembedding software option for general analyses here.

R&S®FE170, R&S®FE170SR, frontend, converter, downconverter

The FC330SR frequency converter is designed for down-conversion of RF signals in the frequency range from 220 GHz to 330 GHz to IF signals.

The video raster analysis option is a versatile tool for analyzing video signals with the RTO6 and RTP oscilloscope series.

The Rohde & Schwarz options support signal integrity debugging and automated compliance testing of DDR5/ LPDDR5, DDR4/ LPDDR4 and DDR3/ DDR3L/ LPDDR3 interfaces. Learn more.

Explore powerful R&S®EMC near field probes for the frequency range from 30 MHz to 3 GHz from test and measurement expert Rohde & Schwarz. Explore now.

The QAR50 automotive radome tester is designed for radome and bumper testing in development and production

The option R&S®RTP-K98 enables to perform wideband load-pull measurements with a setup based on R&S®RTP oscilloscope and R&S®SMW200A.

R&S®FE110, FE110, converter, frontend, downconverter

The external Frontend control software enables the operation of the external Frontends R&S FExx on the R&S RTP oscilloscope.

R&S®GB5400 controller working position – intuitive VCS interface for full controller flexibility and versatility.