Mobile network testing blog

Stories & insights

Mobile network testing

Written by Albert Huang | May 22, 2019

NB-IoT field test: Measuring NB-IoT underground

Singapore was among the first countries to deploy a nationwide narrowband Internet of Things (NB-IoT) network in 2018. In this blog post, we will share an NB-IoT field test procedure, including the results from NB-IoT measurements underground.

NB-IoT field test

“The Internet of Things is a key technology area for growth which will drive Singapore’s Digital Economy for a Smart Nation. We encourage companies to embrace the exciting benefits of NB-IoT as we move towards the digital future” stated Mr. Tan Kiat How, Chief Executive, Infocomm Media Development Authority of Singapore.

As the pioneer in NB-IoT network testing, a Rohde & Schwarz mobile network testing team ventured out into the field to conduct several different NB-IoT test cases. The NB-IoT field tests were performed in a typical tropical environment, in this case in an open field close to the Rohde & Schwarz Regional Headquarters Singapore offices.

The team used the world’s first accurate LTE/NB-IoT coverage measurement solution: the R&S®ROMES4 universal network engineering platform, coupled with an R&S®TSMx scanner, measures NB-IoT coverage accurately and reliably.

NB-IoT coverage measurement solution
NB-IoT coverage measurement solution including the R&S®TSMA scanner and R&S®ROMES4 (left); R&S®TSME scanner (right)

Peek into NB-IoT network performance

The first step to evaluate an NB-IoT network is to measure the base station signals. Technically, this includes measuring the RF signal power level and quality that are received and decoded off the air; this provides the first look into network performance. This measurement has to be performed in a device-agnostic manner to eliminate as many device-related variables and variations as possible.

Using the R&S®TSMA passive scanner, we could identify the base station sites transmitting the NB-IoT signals at our test location.

R&S TSMA scanner
Figure 1: R&S®TSMA scanner in the field (top); R&S®ROMES4 NB-IoT scanner top view N (bottom)
Lightbox öffnen

After identifying the base station signals, we tested the device. In this case, we used a Qualcomm-based module placed in a waterproof housing. By connecting it to R&S®ROMES4, we measured the right levels of the signals that the device received from the network. Testing with a real device enabled us to run end-to-end tests on a live NB-IoT network and measure the realistic performance of the NB-IoT device.

NB-IoT field test

Next, we placed the device on the ground amidst grass 5 cm to 10 cm high. Figure 2 shows that the module attached to the network successfully and acquired an NB-IoT standalone signal.

We can also see the signal power and signal quality that the device receives and verify that there are no issues with the device, SIM registration and measurement setup. In simple terms, this means that the module was able to connect to the network, which is the first step towards success in NB-IoT use cases. In case the module cannot register, we can easily troubleshoot and identify the potential issues with R&S®ROMES4.

Protocol showing successful attach procedure
Figure 2: Protocol showing successful attach procedure (top); receiving signal power and signal quality of device (bottom)
Lightbox öffnen

Coverage of NB-IoT device underground

After verifying the network signals and device performance, it is time to get dirty. To replicate agricultural use cases (for example, crops monitoring) we dug a 20 cm deep hole, placed the module equipped with a sensor at the bottom of the hole and covered it with soil.

In this underground scenario, we observed a noticeable drop of 8 dB in NRSRP received by the device while NRSRQ and NSINR increased, indicating slightly less interference. At the same time, we observed additional NB-IoT parameters such as coverage extension levels and eDRX cycle times. We also monitored power efficiency in both the uplink and downlink.

Figure 3: Measurement results of a NB-IoT device buried 20 centimeters underground
Figure 3: Measurement results of a NB-IoT device buried 20 centimeters underground
Lightbox öffnen

This field test showed which levels an initial NB-IoT network base station transmits and how soil affects the device’s behavior. It is interesting and important to examine the data and potential environmental factors that may affect the results further.

Stay tuned for more NB-IoT test cases and visit our dedicated web page about testing NB-IoT/LTE-M.

This post was co-authored by Lam Pak Lun, Senior Customer Projects Engineer at R&S Singapore.

Related stories

NB-IoT network insights through MIB/SIB demodulation

NB-IoT network insights through MIB/SIB demodulation (part 5)

Read more

NB-IoT: How to find NB-IoT carriers in the spectrum

NB-IoT: How to find NB-IoT carriers in the spectrum (part 6)

Read more

Network measurements with drones

Network measurements with drones: The next step to a connected sky

Read more

Subscribe MNT blog

Sign up for our newsletter

Stay up to date and get stories and insights with our frequent mobile network testing newsletter.

Stories by category

Benchmarking & optimization
Benchmarking & optimization

More information

Field services & interference hunting
Field services & interference hunting

More information

Innovations in mobile network testing
Innovations in mobile network testing

More information

Testing from RF to QoE
Testing from RF to QoE

More information

Informationen anfordern

Haben Sie Fragen oder benötigen Sie weitere Informationen? Nutzen Sie hierzu einfach unser Kontaktformular und wir setzen uns umgehend mit Ihnen in Verbindung.

Ich möchte Informationen von Rohde & Schwarz erhalten per

Marketing-Einverständniserklärung

Was bedeutet das im Einzelnen?

Ich bin damit einverstanden, dass die ROHDE & SCHWARZ GmbH & Co. KG und die im Impressum dieser Website genannte, ROHDE & SCHWARZ zugehörige Gesellschaft oder Niederlassung, mich über den gewählten Kommunikationskanal (E-Mail oder Post) zu Marketing- und Werbezwecken kontaktiert (z.B. zur Übersendung von Informationen über Sonderangebote und Rabattaktionen), die in Zusammenhang mit Produkten und Lösungen aus den Bereichen Messtechnik, sichere Kommunikation, Monitoring and Network Testing, Rundfunk- und Medientechnik sowie Cybersicherheit stehen, aber nicht auf diese beschränkt sind.

Ihre Rechte

Diese Einverständniserklärung kann jederzeit durch Senden einer E-Mail, in deren Betreffzeile "Unsubscribe" steht, an news@rohde-schwarz.com, widerrufen werden. Darüber hinaus enthält jede von uns versandte E-Mail einen Link, durch den das Abbestellen zukünftiger Werbung per E-Mail möglich ist. Weitere Einzelheiten zur Verarbeitung personenbezogener Daten und zum Widerrufsverfahren finden sich in unserer Datenschutzerklärung..

Ihre Anfrage wurde erfolgreich versendet. Wir nehmen in Kürze Kontakt mit Ihnen auf.
An error is occurred, please try it again later.