Búsqueda

R&S®RTP high performance series oscilloscopes benefit from highly accurate measurements, unprecedented speed and a compact form factor. More information.

The external Frontend control software enables the operation of the external Frontends R&S FExx on the R&S RTP oscilloscope.

This option supports automated compliance testing for 100BASE-T, 1000BASE-T, 100BASE-T1 and 1000BASE-T1 Ethernet of options RTO-K22, RTO-K24, RTO-K87, RTP-K22, RTP-K24, RTP-K87, RTP-K98

The Rohde & Schwarz options support signal integrity debugging and automated compliance testing of DDR5/ LPDDR5, DDR4/ LPDDR4 and DDR3/ DDR3L/ LPDDR3 interfaces. Learn more.

The R&S®RTP-K140/141 options enable the high-speed serial pattern trigger function with a maximum nominal data rate of 8 Gbps or 16 Gbps. More info.

The TDR/TDT software option creates a time domain reflection (TDR) and time domain transmission (TDT) analysis system for R&S®RTO or RTP oscilloscopes. Explore now!

The R&S®RTP and RTO oscilloscopes supports triggering and decoding of USB 3.1 Gen 1 and Gen 2 signals. Explore the USB 3.1 triggering & decoding software here.

The option R&S®RTP-K98 enables to perform wideband load-pull measurements with a setup based on R&S®RTP oscilloscope and R&S®SMW200A.

The USB-IF has approved the USB 3.2 compliance test solution from Rohde & Schwarz, confirming that it meets the stringent requirements set by the standardization body. Manufacturers of USB devices can have full confidence in the accuracy and reliability of the test results produced by the test solution.

5 jun 2024 | Comunicado de prensa | Test & measurement

R&S®RTP and R&S®RTO oscilloscopes support TX and RX compliance tests for V1.1/2.0/3.2 Gen 1&2

The R&S®RTP-K114 and R&S®RTP-K115 options enable DP 1.4b and eDP 1.4a/1.5 compliance testing on R&S®RTP oscilloscopes.

Learn how easy it is to configure a equalizer emulation within the Equalizer setup dialog. For interface standards such as USB, PCIe or DP, the necessary S-parameter files are included in the oscilloscope software.

Learn about how to configure cable emulation within the Embedding setup dialog

Learn about key advantages of the Embedding and Equalization option of the R&S RTP & RTO6 oscilloscopes. Start with the Signal Configurator.

The Eye Diagram is an effective tool to validate signal integrity. This video compares the eye diagram on a signal acquired at the output of a USB transmitter versus a waveform with some added cable emulation.

The R&S®RTP and R&S®RTO oscilloscope supports serial triggering and decoding of Automotive Ethernet BroadR-Reach or 100BASE-T1. Explore the features now.

The realtime deembedding of signal path characteristics is based on S-parameters. Learn more about the deembedding software option for general analyses here.

The option R&S RTP-K110 enables HDMI 1.4b/2.1 compliance testing on the R&S RTP oscilloscopes.

Rohde & Schwarz launches its novel wideband modulated load pull solution based on the R&S RTP oscilloscope. It offers an extension to traditional vector network analyzer (VNA)-based solutions for non-linear device characterization by enabling load pull with wideband modulated signals to support RF components development for next-generation wireless technologies.

20 ene 2025 | Comunicado de prensa | Test & measurement

RTP - see the difference. Learn how to perform faster and more in-depth measurements on analog, RF or digital signals.

The high definition (HD) mode increases the vertical resolution of the R&S®RTE, R&S®RTO and R&S®RTP oscilloscopes to up to 16-bit. Benefit from precise analysis results!

The R&S®RTP, R&S®RTO and R&S®RTE oscilloscopes support triggering and decoding of SpaceWire data and communications buses. Explore the SpaceWire triggering and decoding software.

RTP - see the difference. Learn about the powerful capabilities of the RTP oscilloscope to making sure that your design passes EMI test.

The R&S RTP oscilloscope offers a comprehensive set of tools for analysing widebad RF signals together with the external frontends downconverted. Start with powerful trigger events, responsive spectrum analysis or the unique IQ mode to prepare in depth signal analysis.

This video demonstrates how easy the VSE software can analyze a 5G FR2 signal that was captured and downconverted by the FE44S external frontend and acquired by the RTP oscilloscope.

The RTP oscilloscope can use up to 4 external frontends to acquire the respective IF signals for further analysis. Here we use two FE44S external frontends to test a 5G FR2 signal at 28 GHz. Signal analysis is performed by the R&S VSE software running directly on the RTP oscilloscope.

RTP Oscilloscopes with External Frontends - Automotive Radar

RTP- see the difference. Be more productive with the most intuitive oscilloscope user interface.

RTP- see the difference. Use the accuracy of the RTP for the analysis of wide band RF signals.