Mobile network testing blog

Stories & insights

Mobile network testing

Written by Yunuen Wagner | January 12, 2017

Identifying passive intermodulation

Passive intermodulation is nothing new. It has been an issue since the first commercial networks. In GSM, for example, whenever a PIM issue was present, network operators could easily re-allocate frequencies without affecting the service.

Identifying passive intermodulation

With 3G and 4G, however, frequency re-allocation is no longer possible. PIM problems have to be dealt with. They have become even more important as network operators need to push their networks’ spectral efficiency to the theoretical limit to achieve the highest possible data rates.

How can you tell the difference between passive intermodulation and any external interference?

As mentioned in an earlier post, it all starts with low network performance: low signal-to-noise ratio, reduced data rates, dropped calls, reduced coverage, etc., combined with the fact that voltage standing wave ratio (VSWR) measurements, performed at the site, are O.K.

If you can switch the site off and “listen” with a spectrum analyzer, such as the R&S FSH or PiMPro in RX interference mode, it is possible to identify PIM. Passive intermodulation is related to transmitting power. When the power is turned off, and the interference remains, then it is most probably an external interference; is the interference gone, then it is PIM you are dealing with.

RX interference measurement on the PiMPro Tower’s PIM analyzer
RX interference measurement on the PiMPro Tower’s PIM analyzer

Non-linear behavior in passive intermodulation

Alternatively, if you can’t switch the site off, you can vary the TX power and monitor the interference level in the uplink (UL) frequency range. PIM has a non-linear behavior. Raising the TX power by 1 dB will increase the PIM energy in the UL by 3 dB (in practice, around 2.3 dB). With this in mind, you could increase the TX power by a few dBs to determine whether PIM energy is present.

Non-linear behavior in passive intermodulation
Non-linear behavior in passive intermodulation

At this point in time:

  • If you are facing PIM, we recommend inspecting the connectors: clean and torque them properly. One loose connector, moving because of wind, can create PIM levels higher than –60 dBm (tested at 2 x 43 dBm). The PiMPro Tower PIM analyzer can easily help you identify the sources of PIM.
  • If you are facing external interference, Rohde & Schwarz offers a broad product portfolio for the detection and location of radio communication signals, from cost-efficient entry-level to specialized automatic solutions.

There is more to say about PIM; for example, what is the best practice testing for PIM? Learn about our recommended testing procedures here.

Related stories

5G site testing and troubleshooting mobile networks

5G site testing and troubleshooting mobile networks

Read more

PIM testing: Best practices in a nutshell

PIM testing: Best practices in a nutshell

Read more

Are you having trouble spotting interference in your 5G NR TDD network?

Are you having trouble spotting interference in your 5G NR TDD network?

Read more

Subscribe MNT blog

Sign up for our newsletter

Stay up to date and get stories and insights with our frequent mobile network testing newsletter.

Stories by category

Benchmarking & optimization
Benchmarking & optimization

More information

Field services & interference hunting
Field services & interference hunting

More information

Innovations in mobile network testing
Innovations in mobile network testing

More information

Testing from RF to QoE
Testing from RF to QoE

More information

Solicitar información

¿Tiene preguntas o necesita información adicional? Simplemente complete este formulario y nos pondremos en contacto con usted.

Deseo recibir información de Rohde & Schwarz por

Permiso de marketing

Deseo recibir información de marketing o publicidad (p. ej. sobre ofertas especiales y promociones de descuentos) de Rohde & Schwarz GmbH & Co. KG y la entidad o compañía filial de Rohde & Schwarz indicada en la Información legal de este sitio web por correo electrónico o postal. Encontrará información adicional sobre el uso de los datos personales y el procedimiento de retirada en la Declaración de privacidad y la Autorización de marketing.

Se ha enviado su solicitud. Nos pondremos en contacto con usted lo antes posible.
An error is occurred, please try it again later.