EMC, RF/MW components, and more webinars

Our on-demand webinars provide vital input for engineers in charge of RF amplifier efficiency, including deep insights into EMC and coexistence issues, as well as power integrity.
Webinar: From design to real RF device – connecting EDA simulation and hardware test

Webinar: From design to real RF device – connecting EDA simulation and hardware test

Broadcast Date: November 02, 2021

This webinar is intended for engineers who design RF components and systems using tools for simulation and hardware test.

Webinar: mmWave and sub-THz active load-pull, gain compression and S parameter measurements

mmWave and sub-THz active load-pull, gain compression and S parameter measurements

In recent years, there has been a substantial increase in the use of active devices operating at mmWave and sub-terahertz frequencies. Such devices find applications in various industries including automotive, radar, radio astronomy, remote sensing, military and others.

We will examine techniques that measure S-parameters at user-specified power levels, discuss making accurate and repeatable gain compression measurments, as well as non-50 ohm active load-pull measurements on DUTs under large signal conditions which make validating non-linear device models possible, and how to create ideal matching networks to maximize DUT performance.

Doherty amplifier - measurement-aided development

Doherty amplifier - measurement-aided development

This webinar introduces the Doherty amplifier as a special case of the “balanced” amplifier genre. We will discuss design & test challenges and show implementation variants that make it possible to increase output power and improve efficiency.

Using a dual input Doherty measurement setup as a reference, we will describe a measurement-aided design method that can significantly reduce the time to market. Key topics such as calibration, linear and nonlinear measurements, and analysis round out the pragmatic approach.

Power integrity - Challenges, best practices, and test solutions for sensitive electronic designs

Power integrity - Challenges, best practices, and test solutions for sensitive electronic designs

We will be discussing power integrity issues, root causes and countermeasures in sensitive electronic designs. Demonstrating best design & test practices and solutions we will be supporting electronic design engineers effectively and efficiently powering their devices and systems. Measurements in the time & frequency domains provide detailed insights in the design verification.

Radio Equipment Directive (RED) and coexistence

Radio Equipment Directive (RED) and coexistence

The efficient use of spectrum is a key-requirement of the new radio equipment directive (RED). Not only transmitters, but also receivers now have to meet minimum regulatory requirements and need to be tested. This discussion with an EMC testing and regulatory expert goes through all relevant RED regulatory, testing and co-existing topics.

The two pillars of 5G: Energy and spectral efficiency

The two pillars of 5G: Energy and spectral efficiency

The session discusses the twin pillars of 5G deployment by operators: spectral efficiency (capacity) vs. energy efficiency (cost). We try to answer the question of how to increase network capacity while at the same time decreasing the network cost for both 5G FR1 and FR2 wireless networks. We explore both traditional methods of increasing capacity as well as newer methods based on old radar technology that can increase capacity while decreasing costs.

Basic and novel methods for the characterization of mixers with VNAs – part 1

Basic and novel methods for the characterization of mixers with VNAs – part 1

In the first webinar, you will learn how to perform a scalar characterization of the mixer and how to measure the relative phase and group delay. In addition, you get to see the technology for mixers with/without LO access.

Basic and novel methods for the characterization of mixers with VNAs – part 2

Basic and novel methods for the characterization of mixers with VNAs – part 2

You will gain further insights in the second webinar about how to perform mixed gain, group delay and phase measurements in the mmWave range, e.g. up to 110 GHz. You will get to know important calibration techniques.

More webinars

Webinar : Mesures en régime impulsionnel

Oct 22, 2020

Webinar : Analyse d'une liaison série ou horloge

Oct 15, 2020

Webinar: The dual input doherty

Jun 26, 2018

Related webinar series

Electronic design webinars

More information

Webinar overview

More information

Solutions for

リクエスト情報

ご質問や詳細な情報のご要望などがございましたら、こちらのフォームよりお気軽にお問い合わせください。担当者よりご連絡させていただきます。

次の手段によってローデ・シュワルツから情報を受信することを希望します。

マーケティング・パーミッション

詳細について

私は、このウェブサイトの出版物に記載されているRohde & Schwarz GmbH & Co. KGおよびRohde & Schwarzの法人および子会社が、
ここで選択した手段 (電子メールまたは郵便メール) を通じて、マーケティングおよび広告目的 (特別キャンペーンや値引きに関する情報など) で、私に連絡することに同意します。その内容は、電子計測、セキュリティ通信、モニタリングおよびネットワークテスト、放送およびメディア、そしてサイバーセキュリティ分野の製品やソリューションを含みますが、上記に限定されるものではありません。

お客様の権利

この同意表明は、件名が"Unsubscribe"の電子メールをnews@rohde-schwarz.com宛に送信することにより、いつでも取り消すことができます。これに加えて、今後の電子メール広告の購読を停止するためのリンクが、送信されるすべての電子メールに記載されています。個人データの使用と取り消し手順の詳細は、「プライバシーステートメント」に記載されています。

お問い合わせ内容が送信されました。 後ほどご連絡致します。
An error is occurred, please try it again later.