오실로스코프 적용 사례 동영상 – 미디어 센터

The right set up to Decode I²C with an oscilloscope

Discover how to easily decode I²C with the right setup, as shown on an R&S®RTO.

UART/RS232/RS485 Triggering on Break condition

Use the hardware trigger to isolate break conditions. Break conditions can be corellated with their root cause one by one using the History Mode.

Debug RS232, RS485 or UART interfaces

Let your Oscilloscope decode your UART/RS232/RS485 interfaces for you! So you can quickly understand the data and correlate the data content with the electrical signal.

In depth analysis of your RS232 interface

In depth analysis of RS232 interfaces frame by frame using the R&S®RTO decode table and zoom window.

I²C Debugging with hardware trigger of RTO

How to identify and trace down errors in I²C interfaces using the Hardware Trigger together with History Mode.

Possibilities provided by the I²C decode protocol

Dive into your protocol to check for any problems with your I²C interface.

TDR/TDT Analysis with R&S Oscilloscopes

Impedance and transmission loss measurements

Advanced Jitter Analysis with R&S Oscilloscopes

Novel signal model based jitter decomposition algorithm

EMI analysis on power supply design

Design power supplies with EMI in mind and learn more about EMC standards and challenges for power electronics with respect to new semiconductor technologies such as SiC and GaN devices. Understand the EMC debugging process by means of practical examples.

Energy measurement of a pulsed signals

Learn how to measure the energy of a pulsed sine wave signal with advanced math functions.

IQ Mode for RF Signal Analysis

Downconvert RF signals in the oscilloscope and use resulting IQ sample for further analysis with the R&S VSE software or external tools.

Advanced correction of integral math waveforms

Learn how to remove 1/f noise in an integral math waveform for analyzing sinusoidal or pulsed signas with advanced math functions.

77 GHz Automotive Radar (part 1)

Learn more about the basic test setup of aautomotive radar device with a High-Performance RTP Oscilloscope.

77 GHz Automotive Radar (part 2)

Deembed converters and other setup components in realtime.

77 GHz Automotive Radar (part 3)

Demodulate radar pulses with built-in oscilloscope functions.

77 GHz Automotive Radar (part 4)

Perform phase-coherent measurements on multiple antenna signals.

Campus Dashboard - Key Functions

Learn more about key functions of R&S Campus Dashboard software.

Campus Dashboard - Setup & Configuration

Learn how to setup and configure our software for multi-user student labs

Campus Dashboard - Introduction

Time-saving teaching-software for multi-user student labs

Power integrity for distributed systems

This session provides an insight into system-level issues and effective measurement and analysis techniques for achieving optimum system performance with rival requirements.

Decoding CAN Flexible Data CAN-FD bus with a handheld oscilloscope

Discover how to easily deocde CAN-FD using an R&S®RTH handheld oscilloscope.

Probing a differential bus with huge common mode

Discover the best probing method for differential buses, as displayed on an R&S®RTA connected to a differential CAN bus.

Stimulate your device with the built in pattern generator

Discover how to simulate your device under test with a built in pattern generator on the R&S®RTA.

EMI debugging with an oscilloscope

Discover how to debug a power supply using a near field probe and a gated FFT, as shown on an R&S®RTO.

Trigger in frequency domain to with the Zone Trigger to capture burst signals

Discover how to easily capture the RF burst from a keyfob using an R&S®RTO.

Decode Flexray with an oscilloscope

Discover how to easily decode Flexray using an R&S®RTO.

CAN-dbc: symbolic decoding of CAN bus

Discover how to translate decoded hex values into useful words, as displayed on an R&S®RTO.

Current probe measurements with correct grid annotation

Discover how to easily make current probe measurements ith correct grid annotation on an R&S®RTO.

Decoding a CAN Bus

Discover how to decode a CAN Bus with an R&S®RTO, as well as looking at transmission errors and electric signal quality.

Serial bus decoding capability with an Oscilloscope

Discover the powerful decoding capability of Rohde and Schwarz oscilloscopes, as displayed on an R&S®RTO

Decoding over three minutes of bus data using deep memory and ultrasegmentation

Discover how to decode bus data using deep memory and ultrasegmentation, as displayed on an R&S®RTA.

Decoding SENT bus with a handheld oscilloscope

Discover how to easily deocde SENT using an R&S®RTH handheld oscilloscope.

Symbolic decoding of a SENT bus

Discover how to set up symbolic decoding of a SENT bus, as displayed on an R&S®RTO.

Decoding SENT bus signal

Discover how to easily deocde SENT using Rohde and Schwarz oscilloscopes, as displayed on an R&S®RTO.

Decoding LIN with an oscilloscope

Discover how to decode LIN, as displayed on an R&S®RTA.

Triggering and decoding fast channel and slow channel of the SENT bus

Discover how to decode SENT, including enhanced serial messages, displayed on an R&S®RTO.

Debug CAN flexible data CAN-FD interfaces with an oscilloscope

Discover how to debug CAN-FD, as displayed on an R&S®RTO.

Decode CAN bus with a handheld oscilloscope

Discover how to easily deocde a CAN bus using an R&S®RTH handheld oscilloscope.

Decoding CAN Flexible Data CAN-FD bus

Discover how to decode CAN-FD using a R&S®RTO, as well as looking at transmission errors and electric signal quality.

Decoding a CAN Bus

Discover how to decode a CAN Bus with an R&S®RTM, as well as looking at transmission errors and electric signal quality.

Serial bus decoding capability with an Oscilloscope

Discover the powerful decoding capability of Rohde & Schwarz oscilloscopes, as displayed on an R&S®RTM..

Triggering on a CAN Bus

Discover the Bus trigger capability of Rohde and Schwarz oscilloscopes, as displayed on an R&S®RTO or an R&S®RTM.

Decoding over a minute of bus data using deep memory

Discover how Rohde & Schwarz oscilloscpes with deep memory can record over a minute of CAN bus data, as displayed on an R&S®RTO.

1000BASE-T1 cable testing according to OPEN Alliance TC9

A guide to perform cable testing based on unshielded twisted pair (UTP) for 1000BASE-T1 based on the OPEN Alliance TC9 specification.

Integrated arbitrary waveform generator

Every R&S®RTO can be enhanced to include a 100 MHz arbitrary waveform generator.

Flat frequency response for accurate measurement results

The flat frequency response ensures accurate signal acquisition over the R&S®RTO oscilloscope's entire specified bandwidth.

First zone trigger in time and frequency domain

The R&S®RTO oscilloscopes’ zone trigger lets you graphically separate events.

Up to 16 bit vertical resolution

The low-noise frontend and 10 GHz single-core A/D converter are the foundation for the extraordinarily high measurement accuracy and dynamic range of the R&S®RTO oscilloscopes.

Precise measurement due to very low noise level

Minimizing noise was a key goal when designing the R&S®RTO. The result: precise measurements even at the smallest vertical resolutions.

Powerful 100BASE-T1 triggering

Triggering details for 100BASE-T1 Automotive Ethernet using the R&S®RTO with K57 option.

Powerful 100BASE-T1 decoding

Decoding details for 100BASE-T1 Automotive Ethernet using the R&S®RTO with K57 option.

Decoding automotive Ethernet and CAN using R&S scopes

A comparisson between CAN decoding on the R&S®RTM oscilloscope with automotive Ethernet decoding using the K57 option on the R&S®RTO oscilloscope.

1000BASE-T1 compliance testing - Test mode 4: Transmitter distortion test with disturber

A guide to carrying out a 1000BASE-T1 compliance tests with test mode 4 (transmitter distortion test with disturber) on an R&S®RTO. The video gives an overview of how to configure the setup and generate test reports for further analysis.

1000BASE-T1 compliance testing - Test mode 2: MDI jitter and clock frequency

A guide to carrying out a 1000BASE-T1 compliance tests with test mode 2 (MDI jitter and clock frequency) on an R&S®RTO. The video gives an overview of how to configure the setup and generate test reports for further analysis.

1000BASE-T1 compliance testing - Test mode 5: Transmitter power spectral density (PSD), power level and peak differential output

A guide to carrying out a 1000BASE-T1 compliance tests with test mode 5 (transmitter power spectral density) on an R&S®RTO. The video gives an overview of how to configure the setup and generate test reports for further analysis.

1000BASE-T1 compliance testing - Test mode 6: Maximum output droop

A guide to carrying out a 1000BASE-T1 compliance tests with test mode 6 (maximum output droop test) on an R&S®RTO. The video gives an overview of how to configure the setup and generate test reports for further analysis

SPI bus decoding

R&S®RTO oscilloscopes offer a variety of tools for serial interface analysis.

Documentation at the press of a button

R&S®RTO oscilloscopes help you document measurements, including printing and saving screenshots of the screen content.

Dialog boxes with signal flow diagrams

Signal flow diagrams in the dialog boxes visualize the signal processing, making it easier to configure measurements.

Powerful spectrum analysis

Whether you are working with a motor drive, SMPS or power rails, making fast and precise power measurements can be challenging.

Easily customizable waveform display with R&S®SmartGrid technology

Use the R&S®SmartGrid function to configure the display.

Debug an AD converter using digital channels

The R&S®RTO-B1 option offers numerous triggers for debugging and analysis, such as edge, width, pattern and serial pattern.

Signal integrity measurements with jitter analysis

R&S®RTO oscilloscopes are ideally suited for jitter measurements.

Selection of languages

The R&S®RTO oscilloscope's user interface supports multiple languages.

Fast access to important tools

The toolbar at the top of the screen provides access to frequently used functions such as measurements, zoom and FFT.

Industry-leading mask test: quick configuration – reliable results

Mask tests quickly reveal whether a specific signal lies within defined tolerance limits, providing pass/fail evaluation to assess the quality and stability of a device under test.

Deep toolset for signal analysis

R&S®RTO oscilloscopes offer over 90 measurement functions.

Industry-leading 2 Gsample deep memory

In the basic configuration, R&S®RTO oscilloscopes offer 50 Msample acquisition memory per channel.

MSO analysis: unrivaled in its class

Every R&S®RTO can be enhanced to include a mixed signal option.

Advanced user interface

The advanced user interface enables clear orientation thanks to colour coding, as well as having a high-resolution capacitive touchscreen with gesture support.

Quickly find signal faults with 1 million waveforms/s

R&S®RTO oscilloscopes display up to 1 million waveforms/s. To make this possible, Rohde & Schwarz developed an ASIC with optimized signal processing.

Easy selection of instrument setup

The R&S®RTO can save instrument setups for repetitive measurements.

EMI debugging

When debugging EMI problems in electronic circuits, development engineers face the challenging problem of quickly...

Trigger on any signal detail you can see

The unique digital trigger system from Rohde & Schwarz uses the sampling point of the A/D converter in the acquisition path so that the trigger system's input data is identical to the displayed signal.

Setup of the zone trigger at the R&S RTO oscilloscopes

Define up to eight zones of any shape and logically combine them over multiple channels or by using math functions.

Introduction to IoT power consumption measurement

How to perform power consumption measurements on IoT devices.

Evaluating IoT activity phase energy consumption

How to analyze the energy consumption of the activity phase of an IoT device.

Rewind to past waveforms with history mode

This video demonstrates how to use the history mode of the R&S®Scope Rider to analyze recent acquisitions.

Harmonic Analysis

This video demonstrates how to use the harmonic analysis mode of the R&S®Scope Rider to automatically analyze the harmonic content of up to four input signals.

Serial protocol decode

This video demonstrates serial protocol decode on the R&S®Scope Rider.